DTC P0500 Vehicle Speed Sensor "A" |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0500 | While vehicle being driven, no vehicle speed sensor signal transmitted to ECM (2 trip detection logic) |
|
| Related DTCs | P0500: Vehicle speed sensor "A" pulse input error |
| Required Sensors/Components (Main) | Vehicle Speed Sensor (VSS), Combination meter and Skid control ECU |
| Required Sensors/Components (Related) | Park/Neutral Position (PNP) switch, Engine Coolant Temperature (ECT) sensor, Crankshaft Position (CKP) sensor, Throttle Position (TP) sensor and Mass Air Flow (MAF) meter |
| Frequency of Operation | Continuous |
| Duration | 5 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Time after ignition switch off to ON | 3 seconds or more |
| Transfer neutral switch* | Not "N" position |
| Vehicle speed | 9 km/h (5.59 mph) or more |
| Battery voltage | 8 V or more |
| Starter | OFF |
| Vehicle speed sensor signal | No pulse input |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK OPERATION OF SPEEDOMETER |
Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.
|
| ||||
| OK | |
| 2.READ VALUE USING TECHSTREAM (VEHICLE SPEED) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.
Drive the vehicle.
Read the value displayed on the Techstream.
|
| ||||
| OK | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM) |
Disconnect the combination meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H37-35 (+S) - A27-13 (SPD) | Always | Below 1 Ω |
| H37-35 (+S) or A27-13 (SPD) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT COMBINATION METER ASSEMBLY (+S VOLTAGE) |
![]() |
Disconnect the combination meter connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| H37-35 (+S) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Combination Meter) |
|
| ||||
| OK | |
| 5.INSPECT COMBINATION METER ASSEMBLY (SPD SIGNAL OUTPUT) |
![]() |
Remove the combination meter (Click here).
Connect the combination meter.
Move the shift lever to N.
Jack up the vehicle.
Turn the ignition switch to ON.
Check the voltage between the terminal of the combination meter and the body ground while the wheel the is turned slowly
| Tester Connection | Switch Condition | Specified Condition |
| H37-35 (+S) - Body ground | Ignition switch ON (Wheel is turned slowly) | Voltage generated intermittently |
| *a | Front view of wire harness connector (to Combination Meter) |
|
| ||||
| OK | ||
| ||
| 6.INSPECT COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM) |
![]() |
Remove the combination meter (Click here).
Connect the combination meter.
Move the shift lever to N.
Jack up the vehicle.
Turn the ignition switch to ON.
Check the voltage between the terminal of the combination meter and the body ground while the wheel the is turned slowly
| Tester Connection | Switch Condition | Specified Condition |
| H37-36 (SI) - Body ground | Ignition switch ON (Wheel is turned slowly) | Voltage generated intermittently |
| *a | Front view of wire harness connector (to Combination Meter) |
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE ACTUATOR) |
Disconnect the combination meter connector.
Disconnect the brake actuator connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H37-36 (SI) - A19-3 (SPI) | Always | Below 1 Ω |
| H37-36 (SI) or A19-3 (SPI) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||