DTC P2444 Secondary Air Injection System Pump Stuck On Bank1 |
DTC P2445 Secondary Air Injection System Pump Stuck Off Bank1 |
DTC P2446 Secondary Air Injection System Pump Stuck On Bank 2 |
DTC P2447 Secondary Air Injection System Pump Stuck Off Bank 2 |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2444 P2446 | Secondary air pressure more than 3.0 kPa (23 mmHg) despite ECM commanding air pump to turn off (2 trip detection logic) |
|
| P2445 P2447 | Secondary air pressure less than 1.9 kPa (14 mmHg) despite ECM commanding air pump to turn on (2 trip detection logic) |
|
| Related DTCs | P2444: Air pump stuck ON P2445: Air pump stuck OFF P2446: Air pump stuck ON P2447: Air pump stuck OFF |
| Required Sensors/Components (Main) | Pressure sensor |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Once per drive cycle |
| Duration | 7 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0010, P0020 (VVT oil control valve) P0011, P0021 (VVT system - Advance) P0012, P0022 (VVT system - Retard) P0013, P0023 (Exhaust VVT oil control valve) P0014, P0024 (Exhaust VVT system - Advance) P0015, P0025 (Exhaust VVT system - Retard) P0016, P0018 (VVT system - Misalignment) P0017, P0019 (Exhaust VVT system - Misalignment) P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater) P006A, P0107, P0108 (Manifold absolute pressure) P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Front oxygen/Air fuel ratio sensor) P0171, P0172, P0174, P0175 (Fuel system) P0301 - P0308 (Misfire) P0327, P0328, P0332, P0333, P032C, P032D, P033C, P033D (Knock sensor) P0335 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351 - P0358 (Igniter) P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor) P0401 (EGR system) P0451, P0452, P0453 (EVAP system) P0500, P0722 (Vehicle speed sensor) P106B (Evap. emission control system pressure sensor - Air injection system pressure sensor correlation) P1340 (Camshaft position sensor) P1613, P1614 (Secondary air injection driver) P2431, P2432, P02433, P2436, P2437, P2438 (Secondary air injection system pressure sensor) |
| Battery voltage | 11 V or more |
| Atmospheric pressure | 45 kPa (338 mmHg, 13 in.Hg) or more |
| Engine | Running |
| AIR monitor during AIR: ON*1 | Completed |
| AIR monitor during AIR: OFF*2 | Completed |
| AIR injection driver fail (open/short or out of range) | Not detected |
| AIR pressure sensor fail (open/short or out of range) | Not detected |
| *1: AIR monitor during AIR: ON | - |
| Time after AIR in operation | 5 seconds or more |
| AIR pump | ON |
| AIR valve | Open |
| Engine speed | 400 to 3750 rpm |
| Intake air amount | Less than 100 gm/s |
| Time after engine start | 1 second or more |
| *2: AIR monitor during AIR: OFF | - |
| Time after AIR in operation | 10 seconds or more |
| AIR pump | OFF |
| AIR valve | Close |
| Engine speed | Below 3000 rpm |
| AIR monitor during AIR: ON | Completed |
| Time after engine start | 1 second or more |
| Battery voltage | 11 V or higher |
| Atmospheric pressure | 45 kPa (338 mmHg, 13 in.Hg) or higher |
| Engine | Running |
| Air flow pattern check condition during AIR monitor during AIR: ON* | Completed |
| AIR injection driver fail (open/short or out of range) | Not detected |
| AIR pressure sensor fail (open/short or out of range) | Not detected |
| *: Air flow pattern check condition during AIR monitor during AIR: ON | - |
| AIR valve | Open |
| Time after secondary air injection in operation | 1 second or more |
| Either condition is met | (a) or (b) |
| (a) AIR OFF Condition 1 | Met |
| (b) AIR OFF Condition 3 | Met |
| Either condition is met | (a) or (b) |
| (a) AIR ON Condition 2 | Met |
| (b) AIR ON Condition 4 | Met |
| Either condition is met | (a) or (b) |
| (a) Air flow value at Bank 1 or Bank 2 | 160 L/min. or less |
| (b) Air flow value at Bank 1 and Bank 2 | 160 L/min. or less |
| Both conditions are met during AIR ON | - |
| Cumulative pressure pulsation | 18 kPa or higher |
| AIR pressure | 1.9 kPa or higher |
| Both conditions are met during AIR ON | - |
| Cumulative pressure pulsation | 18 kPa or higher |
| AIR pressure | Below 1.9 kPa |
| Both conditions are met during AIR ON | - |
| Cumulative pressure pulsation | Below 18 kPa |
| AIR pressure | 1.9 kPa or higher |
| Both conditions are met during AIR ON | - |
| Cumulative pressure pulsation | Below 18 kPa |
| AIR pressure | Below 1.9 kPa |
| Both conditions are met during AIR OFF | - |
| Cumulative pressure pulsation | 25 kPa or higher |
| AIR pressure | 3 kPa or higher |
| Both conditions are met during AIR OFF | - |
| Cumulative pressure pulsation | 25 kPa or higher |
| AIR pressure | Below 3 kPa |
| Both conditions are met during AIR OFF | - |
| Cumulative pressure pulsation | Below 25 kPa |
| AIR pressure | 3 kPa or higher |
| Both conditions are met during AIR OFF | - |
| Cumulative pressure pulsation | Below 25 kPa |
| AIR pressure | Below 3 kPa |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Air Pump | ON |
| Air Switching Valve | Open |
| Pressure | 1.9 kPa or more |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | OFF |
| Air Switching Valve | Open |
| Pressure | Less than 3.0 kPa |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | ON |
| Air Switching Valve | Closed |
| Pressure | 1.9 kPa or more |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Air Pump | OFF |
| Air Switching Valve | Closed |
| Pressure | Less than 3.0 kPa |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Air Pump | ON |
| Air Switching Valve | Open |
| Pressure | 1.9 kPa or more |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | OFF |
| Air Switching Valve | Open |
| Pressure | Less than 3.0 kPa |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | ON |
| Air Switching Valve | Closed |
| Pressure | 1.9 kPa or more |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Air Pump | OFF |
| Air Switching Valve | Closed |
| Pressure | Less than 3.0 kPa |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Detected Condition while AIR Operating: Air Pump ON, ASV Open | Detected Condition while AIR not Operating: Air Pump OFF, ASV Closed | ECM Determination | DTC Output |
| Case 1 | Case 8 | Normal | - |
| Case 1 | Case 6 | ASV stuck open | P2440 or P2442 |
| Case 1 | Case 7 | Air pump stuck ON | P2444 or P2446 |
| Case 2 | Case 8 | Air pump stuck OFF | P2445 or P2447 |
| Case 3 | Case 8 | ASV stuck closed | P2441 or P2443 |
| Case 1 | Case 5 | ASV stuck open and air pump stuck ON | P2440 and P2444 or P2442 and P2446 |
| Case 2 | Case 6 | ASV stuck open and air pump stuck OFF | P2440 and P2445 or P2442 and P2447 |
| Case 3 | Case 7 | ASV stuck closed and air pump stuck ON | P2441 and P2444 or P2443 and P2446 |
| Case 4 | Case 8 | ASV stuck closed and air pump stuck OFF | P2441 and P2445 or P2443 and P2447 |
| Tester Operation | Air Pump | ASV | Pressure*1 | Pulsation*2 |
| AIR PUMP: ON, ASV: OPEN | ON | OPEN | 1.9 kPa or more | 18 kPa or more |
| AIR PUMP: OFF, ASV: CLOSE | OFF | CLOSE | Less than 3.0 kPa | Less than 25 kPa |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2444, P2445, P2446 AND/OR P2447) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P2444, P2445, P2446 and/or P2447 is output | A |
| DTC P2444, P2445, P2446 and/or P2447 and P0418 and/or P0419 are output | B |
| DTC P2444, P2445, P2446 and/or P2447 and other DTCs (except P0418 and P0419) are output | C |
|
| ||||
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (SECONDARY AIR INJECTION SYSTEM OPERATION) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1: CLOSE, AIR PUMP 2: OFF, ASV2: CLOSE.
Start the engine.
Perform the AIR system intrusive operation while the engine is idling.
Check that the air pump (AIR PUMP), ASV and pressure in the AIR system passage (PRESSURE) displayed on the Techstream indicate the conditions shown in the table below.
| Tester Operation | AIR PUMP | ASV | PRESSURE* |
| AIR PUMP: ON, ASV: OPEN | ON | ON | 1.9 kPa or more |
| AIR PUMP: OFF, ASV: CLOSE | OFF | OFF | Less than 3.0 kPa |
Turn the ignition switch off.
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445, P2446 AND/OR P2247) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Automatic Mode.
Start the engine after the Techstream initialization is finished.
Perform the System Check operation by pressing ENTER (Next).
After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.
Check pending DTCs.
Turn the ignition switch off.
| Result | Proceed to |
| DTC P2444, P2445, P2446 and/or P2447 is output | A |
| Pending DTC is not output | B |
|
| ||||
| A | |
| 4.INSPECT AIR SWITCHING VALVE (PRESSURE SENSOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Air pump pressure (Absolute) and Air Pump2 Pressure (Absolute).
Check the pressure displayed on the Techstream.
|
| ||||
| OK | |
| 5.CHECK AIR INJECTION SYSTEM PIPE CONNECTIONS |

Check that all the pipes and hoses between the air pump and ASV are securely connected.
Inspect the pipes and hoses for blockages and damage.
|
| ||||
| OK | |
| 6.INSPECT AIR INJECTION CONTROL DRIVER (AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT) |
![]() |
Disconnect the AID connectors.
| *a | Front view of wire harness connector (to AID for bank 1) |
| *b | Front view of wire harness connector (to AID for bank 2) |
| *c | Front view of wire harness connector (to AID for bank 1) |
| *d | Front view of wire harness connector (to AID for bank 2) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D32-1 (E) - Body ground | Always | Below 1 Ω |
| D34-1 (E2) - Body ground | Always | Below 1 Ω |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D31-1 (BATT) - Body ground | Always | 11 to 14 V (near battery voltage) |
| D32-5 (+B) - Body ground | Ignition switch ON | 11 to 14 V (near battery voltage) |
| D33-1 (BAT2) - Body ground | Always | 11 to 14 V (near battery voltage) |
| D34-5 (+B2) - Body ground | Ignition switch ON | 11 to 14 V (near battery voltage) |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER) |
Disconnect the ECM connector.
Disconnect the AID connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D56-54 (AIRP) - D32-4 (SIP) | Always | Below 1 Ω |
| D56-53 (ARP2) - D34-4 (SIP2) | Always | Below 1 Ω |
| 56-54 (AIRP) or D32-4 (SIP) - Body ground | Always | 10 kΩ or higher |
| D56-53 (ARP2) or D34-4 (SIP2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.CHECK AIR PUMP |
Check the air pump .
|
| ||||
|
| ||||
| 9.REPLACE AIR PUMP |
Replace the air pump (Click here).
| NEXT | |
| 10.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445, P2446 AND/OR P2447) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Air injection check / Automatic Mode.
Start the engine after the Techstream initialization is finished.
Perform the System Check operation by pressing ENTER (Next).
After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.
Check pending DTCs.
Turn the ignition switch off.
|
| ||||
| OK | ||
| ||
| 11.PERFORM ACTIVE TEST USING TECHSTREAM |
![]() |
Disconnect the AID connectors.
| *a | for Bank 1 |
| *b | Front view of wire harness connector: (to AID for Bank 1) |
| *c | for Bank 2 |
| *d | Front view of wire harness connector: (to AID for Bank 2) |
Connect terminals DI and SIV or DI2 and SIV2 of the wire harness connector for the AID.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN or AIR PUMP 2: ON, ASV 2: OPEN.
Start the engine.
Perform the AIR system forced operation while the engine is idling.
Measure the voltage between the SIV and E or SIV2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.
Turn the ignition switch off.
| Tester Connection | Condition | Specified Condition |
| D32-3 (SIV) - D32-1 (E) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| D34-3 (SIV2) - D34-1 (E2) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| D32-3 (SIV) - D32-1 (E) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
| D34-3 (SIV2) - D34-1 (E2) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
![]() |
Connect terminals DI and SIP or DI2 and SIP2 of the wire harness connector for the AID.
| *a | for Bank 1 |
| *b | Front view of wire harness connector: (to AID for Bank 1) |
| *c | for Bank 2 |
| *d | Front view of wire harness connector: (to AID for Bank 2) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN or AIR PUMP 2: ON, ASV 2: OPEN.
Start the engine.
Perform the AIR system forced operation while the engine is idling.
Measure the voltage between the SIP and E or SIP2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.
Turn the ignition switch off.
| Tester Connection | Condition | Specified Condition |
| D32-4 (SIP) - D32-1 (E) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| D34-4 (SIP2) - D34-1 (E2) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| D32-4 (SIP) - D32-1 (E) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
| D34-4 (SIP2) - D34-1 (E2) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
|
| ||||
| OK | |
| 12.REPLACE AIR INJECTION CONTROL DRIVER |
Replace the air injection control driver (Click here).
| NEXT | |
| 13.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445, P2446 AND/OR P2447) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Air injection check / Automatic Mode.
Start the engine after the Techstream initialization is finished.
Perform the System Check operation by pressing ENTER (Next).
After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.
Check pending DTCs.
Turn the ignition switch off.
|
| ||||
| OK | ||
| ||
| 14.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION) |
Connect the Techstream to the DLC3.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.
Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition | Steady idling | Idling changes from steady to rough idling or engine stall |
| MAP (Data List) | 20 to 40 kPa (150 to 300 mmHg, 6 to 12 in.Hg) | MAP value is at least +10 kPa (75 mmHg, 3 in.Hg) higher than when EGR valve is fully closed |
|
| ||||
| OK | ||
| ||
| 15.INSPECT EGR VALVE |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
|
| ||||
| OK | ||
| ||