Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

DTC    B2602    Key Unlock Warning Switch Circuit Malfunction

for Preparation Click here


DESCRIPTION

A signal (ON or OFF) is sent from the main body ECU to the multiplex tilt and telescopic ECU via the CAN communication bus when the ignition key is inserted into the key cylinder. The multiplex tilt and telescopic ECU uses this signal to operate the auto away or auto return function.

DTC Code
Detection Condition
Trouble Area
B2602
When both conditions below are met:
  1. Unlock warning switch signal is OFF.
  2. Ignition switch is turned ON.
  1. Unlock warning switch
  2. Unlock warning switch circuit
  3. Main body ECU
  4. Multiplex tilt and telescopic ECU

WIRING DIAGRAM


C159013E02


INSPECTION PROCEDURE

1.CHECK OTHER DTC OUTPUT

HINT:
The power tilt and power telescopic steering column system uses the CAN communication system, so check its diagnostic system before proceeding to troubleshooting.

  1. Check if the power tilt and telescopic steering column system DTC B2621 is output.
    Result 
    Result
    Proceed to
    No output
    A
    B2621 is output
    B

    HINT:
    1. If DTC B2621 and B2602 are output, perform troubleshooting for B2621 first.
    2. DTC B2621 indicates a communication interruption for the power tilt and power telescopic steering column system.



B
REPAIR CIRCUIT INDICATED BY OUTPUT DTC (Click here)
A


2.READ VALUE USING TECHSTREAM (UNLOCK WARNING SWITCH COMMUNICATION SIGNAL)
  1. Use the Data List to check if the unlock warning communication signal is functioning properly.

    Tilt & Telescopic 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Key Switch (CAN)
    Communication state of unlock warning switch signal / ON or OFF
    ON: Communication is normal
    OFF: Communication is interrupted
    -

Result 
Result
Proceed to
"OFF" is displayed.
A
"ON" is displayed.
B


B
REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)
A


3.INSPECT UNLOCK WARNING SWITCH

C159210E02

  1. Disconnect the H21 connector from the unlock warning switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Unlock warning switch OFF (Ignition key is removed)
    10 kΩ or higher
    1 - 2
    Unlock warning switch ON (Ignition key is inserted)
    Below 1 Ω



NG
REPLACE UNLOCK WARNING SWITCH (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - UNLOCK WARNING SWITCH)

C159208E02

  1. Disconnect the H1 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H1-5 (KSW) - H21-1
    Always
    Below 1 Ω
    H1-5 (KSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - BODY GROUND)


    C159211E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H21-2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU