Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1787    Rear Occupant Classification Sensor LH Collision Detection

for Preparation Click here


DESCRIPTION

DTC B1787 is stored when the occupant classification ECU receives a collision detection signal, which is sent by the rear occupant detection sensor LH when an accident occurs.
DTC B1787 is also stored when the front seat assembly RH is subjected to a strong impact, even if an actual accident has not occurred.
However, when the occupant classification ECU outputs a collision detection signal, even if the vehicle is not in a collision, DTC B1787 can be cleared by conducting the zero point calibration and sensitivity check.
Therefore, if DTC B1787 is stored, first perform the zero point calibration and sensitivity check.

DTC Code
DTC Detection Condition
Trouble Area
B1787
Either of following conditions is met:
  1. Occupant classification ECU receives collision detection signal, which is sent by rear occupant detection sensor LH when accident occurs
  2. Front seat assembly RH is subjected to strong impact, even if actual accident has not occurred
  1. Front seat assembly RH (Rear occupant detection sensor LH)
  2. Occupant classification ECU

HINT:
  1. When DTC B1650/32 is stored as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1787 of the occupant classification system.
  2. Use the Techstream to check for DTCs of the occupant classification ECU, otherwise the DTCs cannot be read.


WIRING DIAGRAM


B151586E21


INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

1.CHECK FOR DTC
  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the center airbag sensor (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1787 is not output.

    HINT:
    DTCs other than DTC B1787 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.PERFORM ZERO POINT CALIBRATION
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform the zero point calibration (Click here).



NG
Go to step 5
OK


3.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)



NG
Go to step 5
OK


4.CHECK FOR DTC
  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the center airbag sensor (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1787 is not output.

    HINT:
    DTCs other than DTC B1787 may be output at this time, but they are not related to this check.



NG
Go to step 5
OK

END 

5.REPLACE FRONT SEAT ASSEMBLY RH
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the front seat assembly RH.

    1. for Manual seat (Click here)
    2. for Power seat (Click here)

    HINT:
    Perform the inspection using parts from a normal vehicle when possible.


NEXT


6.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform the zero point calibration (Click here).



NG
Go to step 9
OK


7.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)



NG
Go to step 9
OK


8.CHECK FOR DTC
  1. Connect the connectors to the occupant classification ECU and the rear occupant detection sensor LH.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

    HINT:
    1. First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.
    2. Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1787 is not output.

    HINT:
    DTCs other than DTC B1787 may be output at this time, but they are not related to this check.



NG
Go to step 9
OK

END 

9.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle when possible.


NEXT


10.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform the zero point calibration (Click here).


NEXT


11.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)


NEXT

END