Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1793    Occupant Classification Sensor Power Supply Circuit Malfunction

for Preparation Click here


DESCRIPTION

The occupant detection sensor power supply circuit consists of the occupant classification ECU and the occupant detection sensors.
DTC B1793 is stored when a malfunction is detected in the occupant detection sensor power supply circuit.

DTC Code
DTC Detection Condition
Trouble Area
B1793
One of following conditions is met:
  1. Occupant classification ECU receives line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to +B signal in occupant detection sensor power supply circuit for 2 seconds
  2. Open circuit in occupant detection sensor wire harness
  3. Occupant classification ECU malfunction
  1. Front seat assembly RH (Occupant detection sensors)
  2. Front seat wire RH
  3. Occupant classification ECU

HINT:
  1. When DTC B1650/32 is detected as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1793 of the occupant classification system.
  2. Use the Techstream to check for DTCs of the occupant classification ECU, otherwise the DTCs cannot be read.


WIRING DIAGRAM


E146076E03


INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

HINT:
  1. If troubleshooting (wire harness inspection) is difficult to perform, remove the front seat RH installation bolts to see the undersurface of the seat cushion.
  2. In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause problems, such as seat rail deformation. Hold the seat up only for as long as necessary.

1.CHECK FOR DTC
  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

    HINT:
    1. First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.
    2. Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1793 is not output.

    HINT:
    DTCs other than DTC B1793 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK CONNECTION OF CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the occupant classification ECU and the occupant detection sensors.

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


3.CHECK CONNECTOR
  1. Check that the connectors (on the occupant classification ECU side and the occupant detection sensors side) are not damaged (Click here).

    OK:
    Connectors are not deformed or damaged.



NG
REPLACE FRONT SEAT WIRE RH
OK


4.CHECK FRONT SEAT WIRE RH


  1. Disconnect the connectors from the occupant classification ECU and the 4 occupant detection sensors.


    E146259E03

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    W1-11 (SVC1) - Body ground
    Ignition switch ON
    Below 1 V
    W1-12 (SVC2) - Body ground
    W1-5 (SVC3) - Body ground
    W1-6 (SVC4) - Body ground

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    W1-11 (SVC1) - W2-1 (SVC1)
    Ignition switch ON
    Below 1 Ω
    W1-12 (SVC2) - W3-1 (SVC2)
    W1-5 (SVC3) - W4-1 (SVC3)
    W1-6 (SVC4) - W5-1 (SVC4)

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W1-11 (SVC1) - Body ground
    Always
    1 MΩ or higher
    W1-12 (SVC2) - Body ground
    W1-5 (SVC3) - Body ground
    W1-6 (SVC4) - Body ground
    W1-11 (SVC1) - W1-12 (SVC2)
    W1-12 (SVC2) - W1-5 (SVC3)
    W1-12 (SVC2) - W1-6 (SVC4)
    W1-11 (SVC1) - W1-5 (SVC3)



NG
REPLACE FRONT SEAT WIRE RH
OK


5.CHECK FOR DTC
  1. Connect the connectors to the occupant classification ECU and the 4 occupant detection sensors.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

    HINT:
    1. First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.
    2. Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1793 is not output.

HINT:
DTCs other than DTC B1793 may be output at this time, but they are not related to this check.



NG
Go to step 6
OK

USE SIMULATION METHOD TO CHECK (Click here)  

6.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle when possible.


NEXT


7.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform the zero point calibration (Click here).


NEXT


8.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)


NEXT

END