Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1794    Open in Occupant Classification ECU Battery Positive Line

for Preparation Click here


DESCRIPTION

DTC B1794 is stored when a malfunction is detected in the occupant classification ECU.

DTC Code
DTC Detection Condition
Trouble Area
B1794
One of following conditions is met:
  1. Occupant classification ECU circuit malfunction
  2. Occupant classification ECU malfunction
  3. Occupant classification ECU receives short circuit to ground signal in passenger side buckle switch circuit for 2 seconds
  1. Harness or connector
  2. Occupant classification ECU

HINT:
  1. When DTC B1650/32 is detected as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1794 of the occupant classification system.
  2. Use the Techstream to check for DTCs of the occupant classification ECU, otherwise the DTCs cannot be read.


WIRING DIAGRAM


E146100E02


INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

1.CHECK FOR DTC
  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

    HINT:
    1. First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.
    2. Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch off, and wait for at least 10 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1794 is not output.

    HINT:
    DTCs other than DTC B1794 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK CONNECTION OF CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor, occupant detection sensors and occupant classification ECU.

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


3.CHECK CONNECTOR
  1. Check that the connectors (on the occupant classification ECU side) are not damaged (Click here).

    OK:
    Connectors are not deformed or damaged.



NG
REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE)


    H043112E25
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the W6*1 or P14*2 ECU connector.

    HINT:
    *1: for Power Seat
    *2: for Manual Seat

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Resistance:
    for Power Seat 
    Tester Connection
    Condition
    Specified Condition
    W6-3 (GND) - Body ground
    Always
    Below 1 Ω
    for Manual Seat 
    Tester Connection
    Condition
    Specified Condition
    P14-3 (GND) - Body ground
    Always
    Below 1 Ω


    Standard Voltage:
    for Power Seat 
    Tester Connection
    Switch Condition
    Specified Condition
    W6-1 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    W6-7 (IG) - Body ground
    for Manual Seat 
    Tester Connection
    Switch Condition
    Specified Condition
    P14-1 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    P14-7 (IG) - Body ground



NG
REPLACE HARNESS OR CONNECTOR
OK


5.CHECK FOR DTC
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Connect the connectors to the occupant classification ECU.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

    HINT:
    1. First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.
    2. Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch off, and wait for at least 10 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1794 is not output.

    HINT:
    DTCs other than DTC B1794 may be output at this time, but they are not related to this check.



NG
Go to step 6
OK

USE SIMULATION METHOD TO CHECK (Click here)  

6.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle when possible.


NEXT


7.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform the zero point calibration (Click here).


NEXT


8.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)


NEXT

END