Home › Audio/Visual/Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

DTC    01-DF    Master Error

for Preparation Click here


DESCRIPTION


DTC Code
DTC Detection Condition
Trouble Area
01-DF*
The device with a display fails and the master is switched to the audio device.
Also when a communication error between the sub-master (audio) and master occurs, this code is stored.
  1. Radio receiver power source circuit
  1. AVC-LAN circuit between the radio receiver assembly and the component which has stored this code
  1. Radio receiver assembly
  1. Component which has stored this code

HINT:
*: When 210 seconds have elapsed after disconnecting the power supply connector of the master component with the ignition switch ACC or ON, this code is stored.

NOTICE:
  1. Before starting troubleshooting, be sure to clear DTCs to clear codes stored due to the reasons described in Hint above. Then, check for DTCs and troubleshoot according to the output DTCs.
  2. The radio receiver assembly is the master unit.
  3. Be sure to clear and recheck DTCs after the inspection is completed to confirm that no DTCs are output.


WIRING DIAGRAM


E189530E09


INSPECTION PROCEDURE

NOTICE:
Be sure to read Description before performing the following procedures.

1.CHECK RADIO RECEIVER POWER SOURCE CIRCUIT
  1. Refer to Radio Receiver Power Source Circuit (Click here).

    HINT:
    If the power source circuit is operating normally, proceed to the next step.


NEXT


2.INSPECT RADIO RECEIVER ASSEMBLY


    E145834E17
  1. Disconnect the I4*1 and I8*2 radio receiver assembly connectors.

    1. *1: for 14 Speakers
    2. *2: w/ USB Audio System

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I4-5 (ATX+) - I4-15 (ATX-)*1
    Always
    60 to 80 Ω
    I8-9 (TXM+) - I8-10 (TXM-)*2
    Always
    60 to 80 Ω

    1. *1: for 14 Speakers
    2. *2: w/ USB Audio System



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK


3.IDENTIFY COMPONENT WHICH HAS STORED THIS CODE


  1. Enter the diagnostic mode.


    E146440E06

  1. Press the preset switch "channel 3" to change to "Detailed Information Mode".

  1. Identify the component which has stored this code.
    Component Table 
    Component
    Physical Address
    Radio receiver assembly
    190
    "Bluetooth" handsfree module
    19D
    Satellite radio tuner*4
    1F1
    Stereo component amplifier assembly*1
    440
    Multi-media interface ECU*3
    388
    Television display assembly*2
    1B0

    1. *1: for 14 Speakers
    2. *2: w/ Rear Seat Entertainment System
    3. *3: w/ USB Audio System
    4. *4: w/ Satellite Radio

HINT:
  1. "440 (stereo component amplifier)" is the component which has stored this code in the example shown in the illustration.
  2. For details of the DTC display, refer to "DTC Check/Clear" (Click here).


NEXT


4.IDENTIFY COMPONENT WHICH HAS STORED THIS CODE
  1. Select the component which has stored this code.

    HINT:
    The "Bluetooth" handsfree module is built into the radio receiver assembly. If there is a problem between the "Bluetooth" handsfree module and radio receiver assembly, replace the radio receiver assembly.

    Component Table 
    Component
    Proceed to
    Except "Bluetooth" handsfree module and satellite radio tuner
    A
    "Bluetooth" handsfree module (19D)
    B
    Satellite radio tuner (1F1)*
    1. *: w/ USB Audio System



B
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
A


5.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - COMPONENT WHICH HAS STORED THIS CODE)

HINT:
For details of connectors, refer to Terminals of ECU (Click here).

  1. Referring to the AVC-LAN wiring diagram, check the AVC-LAN circuit between the radio receiver assembly and the component which has stored this code.

    1. Disconnect all connectors between the radio receiver assembly and the component which has stored this code.

    2. Check for an open or short in the AVC-LAN circuit between the radio receiver assembly and the component which has stored this code.

      OK:
      There is no open or short circuit.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE RADIO RECEIVER ASSEMBLY
  1. Replace the radio receiver assembly (Click here).

    OK:
    Same problem does not occur.



NG
REPLACE COMPONENT WHICH HAS STORED THIS CODE
OK

END