Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR

BACK DOOR > REASSEMBLY

for Preparation Click here



1. INSTALL REAR SPOILER COVER


    B191672E01
  1. Engage the 5 pins and install the rear spoiler cover.



    B191671
  1. Tighten the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



    B191670
  1. Install the 2 hole plugs.

  1. Connect the connector.



2. INSTALL REAR LIGHT ASSEMBLY RH


    E161831
  1. Engage the clip and install the rear light.

  1. Tighten the 2 nuts.

    Torque:
    6.4 N*m{ 65 kgf*cm , 56 in.*lbf }

  1. Connect the connector.



3. INSTALL REAR LIGHT ASSEMBLY LH


    E161831
  1. Engage the clip and install the rear light.

  1. Tighten the 2 nuts.

    Torque:
    6.4 N*m{ 65 kgf*cm , 56 in.*lbf }

  1. Connect the connector.



4. INSTALL BACK DOOR LOCK (w/o Power Back Door)


    B190532
  1. Install the back door lock with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.

  1. Engage the clamp.



5. INSTALL BACK DOOR LOCK (w/ Power Back Door)


    B194235
  1. Install the back door lock with the 4 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.

  1. Engage the clamp.



6. INSTALL BACK DOOR LOCK PROTECTOR


    B190533
  1. Engage the 2 claws and install the back door lock protector sub-assembly.



7. INSTALL BACK DOOR OUTSIDE HANDLE


    B190531
  1. Install the back door outside handle with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Engage the clamp.

  1. Connect the connector.



8. INSTALL LICENSE PLATE LIGHT ASSEMBLY


    E161800
  1. Tighten the 4 screws.

  1. Connect the 4 harness clamps and install the license plate light.



9. INSTALL REAR TELEVISION CAMERA ASSEMBLY (w/ Rear View Monitor System)


    E192392
  1. Engage the 2 claws and install the rear television camera.



    E192391
  1. Connect the connector.



10. INSTALL BACK DOOR OUTSIDE GARNISH


B191713
  1. Engage the 2 clips and install the back door outside garnish.



    B191712
  1. Tighten the 4 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the connector.



11. INSTALL BACK DOOR LOCK CYLINDER


    B190530
  1. Install the back door lock cylinder with the 2 nuts.

  1. Connect the connector.



12. INSTALL BACK DOOR POWER WINDOW REGULATOR ASSEMBLY


B190529E01
  1. Apply MP grease to the sliding and rotating areas of the back door power window regulator.

  1. Insert the back door power window regulator into the door panel. Provisionally tighten nut A to hang the back door power window regulator on the door panel.

    NOTICE:
    Do not drop the back door power window regulator as it may be damaged.

  1. Install the back door power window regulator with the 5 nuts, and tighten nut A.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



13. INSTALL BACK DOOR GLASS


B190528
  1. Install the back door glass onto the back door power window regulator with the 4 bolts.

    NOTICE:
    Do not damage the glass.

  1. Connect the 2 connectors.



    B190513
  1. Install the hole plug.



14. INSTALL BACK DOOR GLASS RUN


B190527
  1. Install a new back door glass run.



15. INSTALL BACK DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY


    B195693
  1. Engage the 9 claws and install the back door glass outer weatherstrip.



16. INSTALL BACK DOOR OUTSIDE MOULDING LH


    B191708
  1. Engage the 5 clips and install the new back door outside moulding.



17. INSTALL BACK DOOR OUTSIDE MOULDING RH

HINT:
Use the same procedure as for the LH side.



18. INSTALL LINEAR WIPER STEP RH


B190526
  1. Engage the claw and guide and install the liner wiper step.



19. INSTALL REAR WIPER MOTOR GROMMET


E139081E02
  1. Apply MP grease to the entire surface of the wiper motor grommet lip.

    HINT:
    Make sure that the hole does not get clogged with grease and the grooves on the lip are filled with grease.



    E162547E01
  1. Install the rear wiper motor grommet with the mark directed up.



20. INSTALL REAR WIPER MOTOR ASSEMBLY


    E161698
  1. Install the rear wiper motor with the 3 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the connector and clamp.



21. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY


    E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, and then stop the windshield wiper motor in the automatic stop position.



    E162548E01
  1. Install the rear wiper arm into the position shown in the illustration with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    Position the rear wiper arm on the linear wiper step before tightening the nut.

    HINT:
    Hold the arm hinge down by hand while tightening the nut.



22. INSTALL REAR WIPER ARM HEAD CAP


    E161700
  1. Engage the claw and install the rear wiper head cap.



23. INSTALL POWER BACK DOOR SENSOR RH


24. INSTALL POWER BACK DOOR SENSOR LH


25. INSTALL BACK DOOR NO. 2 SERVICE HOLE COVER


B190525
  1. Engage the 2 clips and install the back door No. 2 service hole cover with the 3 screws.



26. INSTALL MULTIPLEX NETWORK BODY ECU (w/ Power Back Door)


B194490
  1. Install the multiplex network body ECU with the 2 screws.

  1. Connect the 2 connector and engage the 2 clamps.



27. INSTALL POWER BACK DOOR WARNING BUZZER (w/ Power Back Door)


    B190524
  1. Engage the clamp and install the power back door warning buzzer.

  1. Connect the connector.



28. INSTALL BACK DOOR SERVICE HOLE COVER


B190522
  1. Apply butyl tape to the door panel, then install a new back door service hole cover as shown in the illustration.

    HINT:
    1. There should be no wrinkles or folds after attaching the service hole cover.
    2. After attaching the service hole cover, check the quality of the seal.



29. INSTALL BACK DOOR GLASS WEATHERSTRIP


B195435
  1. Install a new back door glass weatherstrip on the back door trim board assembly and fold down the 9 claws, as shown in the illustration.



30. INSTALL BACK DOOR TRIM BOARD ASSEMBLY


B190520
  1. Engage the 11 clips and install the back door trim board assembly.



31. INSTALL BACK DOOR PULL STRAP


B190519
  1. Install the back door pull strap with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



32. INSTALL BACK DOOR STRAP COVER


B195035
  1. Engage the claw and slid the back door strap cover as shown in the illustration, and install it.



33. INSTALL BACK DOOR STAY LOWER BRACKET (w/ Power Back Door)


    B194233
  1. Install the back door stay lower bracket with the 2 bolts.

    Torque:
    14 N*m{ 140 kgf*cm , 10 ft.*lbf }



34. INSTALL BACK DOOR SIDE GARNISH LH


B190516
  1. Engage the 3 clips and install the back door side garnish LH.



35. INSTALL BACK DOOR SIDE GARNISH RH


B190515
  1. Engage the 2 clips and install the back door side garnish RH.



36. INSTALL BACK DOOR CENTER GARNISH


B190514
  1. Engage the 4 clips and the claw and install the back door center garnish.



37. INSTALL POWER BACK DOOR ROD (w/ Power Back Door)


B194234
  1. Install the power back door rod with the 2 stop rings.



38. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

CAUTION:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).



39. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).