AUDIO AND VISUAL SYSTEM > Speaker Circuit (Independent Amplifier) |


| 1.CHECK SPEAKER |
Check the malfunctioning speakers.
| Result | Proceed to |
| Malfunction in front speaker area | A |
| Malfunction in rear speaker area | B |
|
| ||||
| A | |
| 2.CHECK SPEAKER |
Check the malfunctioning speakers.
| Result | Proceed to |
| Front No. 1 speaker assembly | A |
| Front No. 2 speaker assembly | B |
| Front No. 3 speaker assembly | C |
| Front No. 4 speaker assembly | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
![]() |
Disconnect the L8*1 and/or M10*2 front No. 1 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 1.8 to 2.6 Ω |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 1 SPEAKER) |
![]() |
Disconnect the I31 stereo component amplifier assembly connector.
Disconnect the L8*1 and/or M10*2 front No. 1 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I31-2 (WFR+) - L8-1 | Always | Below 1 Ω |
| I31-6 (WFR-) - L8-2 | Always | Below 1 Ω |
| I31-2 (WFR+) - Body ground | Always | 10 kΩ or higher |
| I31-6 (WFR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| I31-1 (WFL+) - M10-1 | Always | Below 1 Ω |
| I31-5 (WFL-) - M10-2 | Always | Below 1 Ω |
| I31-1 (WFL+) - Body ground | Always | 10 kΩ or higher |
| I31-5 (WFL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
![]() |
Disconnect the I10*1 and/or I12*2 front No. 2 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (+) - 3 (TWR+) | Always | Below 1 Ω |
| 2 (-) - 4 (TWR-) | Always | Below 1 Ω |
| 3 (TWR+) - 4 (TWR-) | Always | 1.5 to 2.5 Ω |
| Tester Connection | Condition | Specified Condition |
| 1 (+) - 3 (TWL+) | Always | Below 1 Ω |
| 2 (-) - 4 (TWL-) | Always | Below 1 Ω |
| 3 (TWL+) - 4 (TWL-) | Always | 1.5 to 2.5 Ω |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 2 SPEAKER) |
![]() |
Disconnect the I19 stereo component amplifier assembly connector.
Disconnect the I10*1 and/or I12*2 front No. 2 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I19-10 (FR+) - I10-3 (TWR+) | Always | Below 1 Ω |
| I19-9 (FR-) - I10-4 (TWR-) | Always | Below 1 Ω |
| I19-10 (FR+) - Body ground | Always | 10 kΩ or higher |
| I19-9 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| I19-3 (FL+) - I12-3 (TWL+) | Always | Below 1 Ω |
| I19-8 (FL-) - I12-4 (TWL-) | Always | Below 1 Ω |
| I19-3 (FL+) - Body ground | Always | 10 kΩ or higher |
| I19-8 (FL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 7.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY |
![]() |
Disconnect the L1*1 and/or M1*2 front No. 3 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 3 | Always | 3.0 to 4.2 Ω |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 3 SPEAKER) |
![]() |
Disconnect the I10*1 and/or I12*2 front No. 2 speaker assembly connector.
Disconnect the L1*1 and/or M1*2 front No. 3 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I10-1 (+) - L1-3 | Always | Below 1 Ω |
| I10-2 (-) - L1-1 | Always | Below 1 Ω |
| I10-1 (+) - Body ground | Always | 10 kΩ or higher |
| I10-2 (-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| I12-1 (+) - M1-3 | Always | Below 1 Ω |
| I12-2 (-) - M1-1 | Always | Below 1 Ω |
| I12-1 (+) - Body ground | Always | 10 kΩ or higher |
| I12-2 (-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 9.INSPECT FRONT NO. 4 SPEAKER ASSEMBLY |
![]() |
Disconnect the I14 front No. 4 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 1.5 to 2.1 Ω |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 4 SPEAKER) |
![]() |
Disconnect the I31 stereo component amplifier assembly connector.
Disconnect the I14 front No. 4 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I31-3 (CTR+) - I14-1 | Always | Below 1 Ω |
| I31-9 (CTR-) - I14-2 | Always | Below 1 Ω |
| I31-3 (CTR+) - Body ground | Always | 10 kΩ or higher |
| I31-9 (CTR-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 11.CHECK SPEAKER |
Check the malfunctioning speakers.
| Result | Proceed to |
| Rear No. 2 speaker assembly | A |
| Rear No. 1 speaker assembly | B |
| Quarter side speaker assembly | C |
| w/ Box No. 1 speaker assembly | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 12.INSPECT REAR NO. 2 SPEAKER ASSEMBLY |
![]() |
Disconnect the N2*1 and/or N8*2 rear No. 2 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (-TW) - 3 (+TW) | Always | 3.0 to 4.2 Ω |
| 1 (-TW) - 2 (-) | Always | Below 1 Ω |
| 3 (+TW) - 4 (+) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - REAR NO. 2 SPEAKER) |
![]() |
Disconnect the I19 stereo component amplifier assembly connector.
Disconnect the N2*1 and/or N8*2 rear No. 2 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I19-5 (RR+) - N2-3 (+TW) | Always | Below 1 Ω |
| I19-12 (RR-) - N2-1 (-TW) | Always | Below 1 Ω |
| I19-5 (RR+) - Body ground | Always | 10 kΩ or higher |
| I19-12 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| I19-4 (RL+) - N8-3 (+TW) | Always | Below 1 Ω |
| I19-11 (RL-) - N8-1 (-TW) | Always | Below 1 Ω |
| I19-4 (RL+) - Body ground | Always | 10 kΩ or higher |
| I19-11 (RL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 14.INSPECT REAR NO. 1 SPEAKER ASSEMBLY |
![]() |
Disconnect the N1*1 and/or N7*2 rear No. 1 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 1.8 to 2.6 Ω |
|
| ||||
| OK | |
| 15.CHECK HARNESS AND CONNECTOR (REAR NO. 2 SPEAKER - REAR NO. 1 SPEAKER) |
![]() |
Disconnect the N2*1 and/or N8*2 rear No. 2 speaker connector.
Disconnect the N1*1 and/or N7*2 rear No. 1 speaker connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N2-4 (+) - N1-1 | Always | Below 1 Ω |
| N2-2 (-) - N1-2 | Always | Below 1 Ω |
| N2-4 (+) - Body ground | Always | 10 kΩ or higher |
| N2-2 (-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| N8-4 (+) - N7-1 | Always | Below 1 Ω |
| N8-2 (-) - N7-2 | Always | Below 1 Ω |
| N8-4 (+) - Body ground | Always | 10 kΩ or higher |
| N8-2 (-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 16.INSPECT QUARTER SIDE SPEAKER ASSEMBLY |
![]() |
Disconnect the O37*1 and/or O31*2 quarter side speaker connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 1.5 to 2.5 Ω |
|
| ||||
| OK | |
| 17.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - QUARTER SIDE SPEAKER) |
![]() |
Disconnect the I31 and I19 stereo component amplifier assembly connectors.
Disconnect the O37*1 and/or O31*2 quarter side speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I19-2 (SR+) - O37-1 | Always | Below 1 Ω |
| I19-7 (SR-) - O37-2 | Always | Below 1 Ω |
| I19-2 (SR+) - Body ground | Always | 10 kΩ or higher |
| I19-7 (SR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| I31-8 (SL+) - O31-1 | Always | Below 1 Ω |
| I31-7 (SL-) - O31-2 | Always | Below 1 Ω |
| I31-8 (SL+) - Body ground | Always | 10 kΩ or higher |
| I31-7 (SL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 18.INSPECT W/ BOX NO.1 SPEAKER ASSEMBLY |
![]() |
Disconnect the O13 w/ box No. 1 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (WF1+) - 2 (WF1-) | Always | 1.6 to 2.4 Ω |
| 3 (WF2+) - 4 (WF2-) | Always | 1.6 to 2.4 Ω |
|
| ||||
| OK | |
| 19.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - W/ BOX NO. 1 SPEAKER) |
![]() |
Disconnect the I31 and I19 stereo component amplifier assembly connectors.
Disconnect the O13 w/ box No. 1 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I19-1 (WF1+) - O13-1 (WF1+) | Always | Below 1 Ω |
| I19-6 (WF1-) - O13-2 (WF1-) | Always | Below 1 Ω |
| I31-4 (WF2+) - O13-3 (WF2+) | Always | Below 1 Ω |
| I31-10 (WF2-) - O13-4 (WF2-) | Always | Below 1 Ω |
| I19-1 (WF1+) - Body ground | Always | 10 kΩ or higher |
| I19-6 (WF1-) - Body ground | Always | 10 kΩ or higher |
| I31-4 (WF2+) - Body ground | Always | 10 kΩ or higher |
| I31-10 (WF2-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||