Home › Audio/Visual/Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for DVD)

NAVIGATION SYSTEM (for DVD) > Speaker Circuit

for Preparation Click here


DESCRIPTION

The stereo component amplifier assembly sends sound signals to the speaker.

WIRING DIAGRAM


E173185E04


E160611E05


INSPECTION PROCEDURE

1.CHECK SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Malfunction in front speaker area
    A
    Malfunction in rear speaker area
    B



B
Go to step 11
A


2.CHECK SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Front No. 1 speaker assembly
    A
    Front No. 2 speaker assembly
    B
    Front No. 3 speaker assembly
    C
    Front No. 4 speaker assembly
    D



B
Go to step 5

C
Go to step 7

D
Go to step 9
A


3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E144966
  1. Disconnect the L8*1 and/or M10*2 front No. 1 speaker connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.8 to 2.6 Ω



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 1 SPEAKER)


    E160615E03
  1. Disconnect the I31 stereo component amplifier assembly connector.

  1. Disconnect the L8*1 and/or M10*2 front No. 1 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    I31-2 (WFR+) - L8-1
    Always
    Below 1 Ω
    I31-6 (WFR-) - L8-2
    I31-2 (WFR+) - Body ground
    Always
    10 kΩ or higher
    I31-6 (WFR-) - Body ground
    for LH:
    Tester Connection
    Condition
    Specified Condition
    I31-1 (WFL+) - M10-1
    Always
    Below 1 Ω
    I31-5 (WFL-) - M10-2
    I31-1 (WFL+) - Body ground
    Always
    10 kΩ or higher
    I31-5 (WFL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)  

5.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    E144969E31
  1. Disconnect the I10*1 and/or I12*2 front No. 2 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 3 (TWR+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWR-)
    3 (TWR+) - 4 (TWR-)
    Always
    1.5 to 2.5 Ω
    for LH:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 3 (TWL+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWL-)
    3 (TWL+) - 4 (TWL-)
    Always
    1.5 to 2.5 Ω



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 2 SPEAKER)


    E160616E04
  1. Disconnect the I19 stereo component amplifier assembly connector.

  1. Disconnect the I10*1 and/or I12*2 front No. 2 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    I19-10 (FR+) - I10-3 (TWR+)
    Always
    Below 1 Ω
    I19-9 (FR-) - I10-4 (TWR-)
    I19-10 (FR+) - Body ground
    Always
    10 kΩ or higher
    I19-9 (FR-) - Body ground
    for LH:
    Tester Connection
    Condition
    Specified Condition
    I19-3 (FL+) - I12-3 (TWL+)
    Always
    Below 1 Ω
    I19-8 (FL-) - I12-4 (TWL-)
    I19-3 (FL+) - Body ground
    Always
    10 kΩ or higher
    I19-8 (FL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)  

7.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    E160614
  1. Disconnect the L1*1 and/or M1*2 front No. 3 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Always
    3.0 to 4.2 Ω



NG
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 3 SPEAKER)
  1. *1: for RH
  2. *2: for LH


    E146500E02
  1. Disconnect the I10*1 and/or I12*2 front No. 2 speaker assembly connector.

  1. Disconnect the L1*1 and/or M1*2 front No. 3 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    I10-1 (+) - L1-3
    Always
    Below 1 Ω
    I10-2 (-) - L1-1
    I10-1 (+) - Body ground
    Always
    10 kΩ or higher
    I10-2 (-) - Body ground
    for LH:
    Tester Connection
    Condition
    Specified Condition
    I12-1 (+) - M1-3
    Always
    Below 1 Ω
    I12-2 (-) - M1-1
    I12-1 (+) - Body ground
    Always
    10 kΩ or higher
    I12-2 (-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)  

9.INSPECT FRONT NO. 4 SPEAKER ASSEMBLY


    E146506
  1. Disconnect the I14 front No. 4 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω



NG
REPLACE FRONT NO. 4 SPEAKER ASSEMBLY (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 4 SPEAKER)


    E160617E03
  1. Disconnect the I31 stereo component amplifier assembly connector.

  1. Disconnect the I14 front No. 4 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I31-3 (CTR+) - I14-1
    Always
    Below 1 Ω
    I31-9 (CTR-) - I14-2
    I31-3 (CTR+) - Body ground
    Always
    10 kΩ or higher
    I31-9 (CTR-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)  

11.CHECK SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Rear No. 2 speaker assembly
    A
    Rear No. 1 speaker assembly
    B
    Quarter side speaker assembly
    C
    w/ Box No. 1 speaker assembly
    D



B
Go to step 14

C
Go to step 16

D
Go to step 18
A


12.INSPECT REAR NO. 2 SPEAKER ASSEMBLY


    E160614E22
  1. Disconnect the N2*1 and/or N8*2 rear No. 2 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (-TW) - 3 (+TW)
    Always
    3.0 to 4.2 Ω
    1 (-TW) - 2 (-)
    Always
    Below 1 Ω
    3 (+TW) - 4 (+)



NG
REPLACE REAR NO. 2 SPEAKER ASSEMBLY (Click here)
OK


13.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - REAR NO. 2 SPEAKER)


    E160618E03
  1. Disconnect the I19 stereo component amplifier assembly connector.

  1. Disconnect the N2*1 and/or N8*2 rear No. 2 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    I19-5 (RR+) - N2-3 (+TW)
    Always
    Below 1 Ω
    I19-12 (RR-) - N2-1 (-TW)
    I19-5 (RR+) - Body ground
    Always
    10 kΩ or higher
    I19-12 (RR-) - Body ground
    for LH:
    Tester Connection
    Condition
    Specified Condition
    I19-4 (RL+) - N8-3 (+TW)
    Always
    Below 1 Ω
    I19-11 (RL-) - N8-1 (-TW)
    I19-4 (RL+) - Body ground
    Always
    10 kΩ or higher
    I19-11 (RL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)  

14.INSPECT REAR NO. 1 SPEAKER ASSEMBLY


    E144966
  1. Disconnect the N1*1 and/or N7*2 rear No. 1 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.8 to 2.6 Ω



NG
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)
OK


15.CHECK HARNESS AND CONNECTOR (REAR NO. 1 SPEAKER - REAR NO. 2 SPEAKER)
  1. *1: for RH
  2. *2: for LH


    E149222E02
  1. Disconnect the N2*1 and/or N8*2 rear No. 2 speaker assembly connector.

  1. Disconnect the N1*1 and/or N7*2 rear No. 1 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    N2-4 (+) - N1-1
    Always
    Below 1 Ω
    N2-2 (-) - N1-2
    N2-4 (+) - Body ground
    Always
    10 kΩ or higher
    N2-2 (-) - Body ground
    for LH:
    Tester Connection
    Condition
    Specified Condition
    N8-4 (+) - N7-1
    Always
    Below 1 Ω
    N8-2 (-) - N7-2
    N8-4 (+) - Body ground
    Always
    10 kΩ or higher
    N8-2 (-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)  

16.INSPECT QUARTER SIDE SPEAKER ASSEMBLY


    E146506
  1. Disconnect the O37*1 and/or O31*2 quarter side speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.5 Ω



NG
REPLACE QUARTER SIDE SPEAKER ASSEMBLY (Click here)
OK


17.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - QUARTER SIDE SPEAKER)


    E160621E03
  1. Disconnect the I31 and I19 stereo component amplifier assembly connectors.

  1. Disconnect the O37*1 and/or O31*2 quarter side speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    I19-2 (SR+) - O37-1
    Always
    Below 1 Ω
    I19-7 (SR-) - O37-2
    I19-2 (SR+) - Body ground
    Always
    10 kΩ or higher
    I19-7 (SR-) - Body ground
    for LH:
    Tester Connection
    Condition
    Specified Condition
    I31-8 (SL+) - O31-1
    Always
    Below 1 Ω
    I31-7 (SL-) - O31-2
    I31-8 (SL+) - Body ground
    Always
    10 kΩ or higher
    I31-7 (SL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)  

18.INSPECT W/ BOX NO. 1 SPEAKER ASSEMBLY


    E160619E03
  1. Disconnect the O13 w/ Box No. 1 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (WF1+) - 2 (WF1-)
    Always
    1.6 to 2.4 Ω
    3 (WF2+) - 4 (WF2-)
    Always
    1.6 to 2.4 Ω



NG
REPLACE W/ BOX NO. 1 SPEAKER ASSEMBLY (Click here)
OK


19.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - W/ BOX NO. 1 SPEAKER)


    E160620E04
  1. Disconnect the I31 and I19 stereo component amplifier assembly connectors.

  1. Disconnect the O13 w/ Box No. 1 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I19-1 (WF1+) - O13-1 (WF1+)
    Always
    Below 1 Ω
    I19-6 (WF1-) - O13-2 (WF1-)
    I31-4 (WF2+) - O13-3 (WF2+)
    I31-10 (WF2-) - O13-4 (WF2-)
    I19-1 (WF1+) - Body ground
    Always
    10 kΩ or higher
    I19-6 (WF1-) - Body ground
    I31-4 (WF2+) - Body ground
    I31-10 (WF2-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)