REAR VIEW MONITOR SYSTEM (w/ Navigation System) > Display Signal Circuit between Navigation Receiver Assembly and Television Camera Assembly |


| 1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY) |
for DVD Navigation System:
Disconnect the I7 navigation receiver assembly connector.
Disconnect the V17 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I7-22 (V+) - V17-2 (CV+) | Always | Below 1 Ω |
| I7-23 (V-) - V17-1 (CV-) | Always | Below 1 Ω |
| I7-21 (CGND) - V17-3 (CGND) | Always | Below 1 Ω |
| I7-24 (CA+) - V17-4 (CB+) | Always | Below 1 Ω |
| I7-22 (V+) - Body ground | Always | 10 kΩ or higher |
| I7-23 (V-) - Body ground | Always | 10 kΩ or higher |
| I7-21 (CGND) - Body ground | Always | 10 kΩ or higher |
| I7-24 (CA+) - Body ground | Always | 10 kΩ or higher |
for SD Navigation System:
Disconnect the I28 navigation receiver assembly connector.
Disconnect the V17 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I28-11 (V+) - V17-2 (CV+) | Always | Below 1 Ω |
| I28-12 (V-) - V17-1 (CV-) | Always | Below 1 Ω |
| I28-14 (CGND) - V17-3 (CGND) | Always | Below 1 Ω |
| I28-13 (CA+) - V17-4 (CB+) | Always | Below 1 Ω |
| I28-11 (V+) - Body ground | Always | 10 kΩ or higher |
| I28-12 (V-) - Body ground | Always | 10 kΩ or higher |
| I28-14 (CGND) - Body ground | Always | 10 kΩ or higher |
| I28-13 (CA+) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.CHECK NAVIGATION RECEIVER ASSEMBLY |
![]() |
for DVD Navigation System:
Disconnect the I7 navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I7-21 (CGND) - Body ground | Always | Below 1 Ω |
| I7-23 (V-) - Body ground | Always | Below 1 Ω |
![]() |
for SD Navigation System:
Disconnect the I28 navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I28-12 (V-) - Body ground | Always | Below 1 Ω |
| I28-14 (CGND) - Body ground | Always | Below 1 Ω |
| *a | Component without harness connected (Navigation Receiver Assembly) |
|
| ||||
| OK | |
| 3.CHECK NAVIGATION RECEIVER ASSEMBLY |
![]() |
Disconnect the V17 rear television camera assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| V17-4 (CB+) - V17-3 (CGND) | Ignition switch ON, shift lever in R | 5.5 to 7.05 V |
| *a | Front view of wire harness connector (to Rear Television Camera Assembly) |
|
| ||||
| OK | |
| 4.CHECK REAR TELEVISION CAMERA ASSEMBLY |
for DVD Navigation System:
Using an oscilloscope, check the waveform.

| *a | Component with harness connected (Navigation Receiver Assembly) | *b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronized Signal |
| *e | Video Waveform | - | - |
| Item | Content |
| Terminal No. (Symbol) | I7-22 (V+) - I7-23 (V-) |
| Tool Setting | 0.2 V/DIV., 50 μs/DIV. |
| Condition |
|
for SD Navigation System:
Using an oscilloscope, check the waveform.

| *a | Component with harness connected (Navigation Receiver Assembly) | *b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronized Signal |
| *e | Video Waveform | - | - |
| Item | Content |
| Terminal No. (Symbol) | I28-11 (V+) - I28-12 (V-) |
| Tool Setting | 0.2 V/DIV., 50 μs/DIV. |
| Condition |
|
|
| ||||
| OK | ||
| ||