Home › Audio/Visual/Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

DTC    74-40    Short in Speaker Circuit

for Preparation Click here


DESCRIPTION


DTC Code
DTC Detection Condition
Trouble Area
74-40
A short is detected in the speaker output circuit.
  1. Harness or connector
  2. Speaker
  3. Stereo component amplifier assembly

WIRING DIAGRAM


E173185E03


E160611E04


INSPECTION PROCEDURE

HINT:
After the inspection is completed, clear the DTCs.

1.CHECK FOR DTC
  1. Disconnect the I31 and I19 stereo component amplifier assembly connectors.

  1. Clear the DTC.

  1. Check if DTC 74-40 is output.

    OK:
    DTC 74-40 is not output.



NG
REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)
OK


2.CHECK FOR DTC
  1. Reconnect the I31 stereo component amplifier assembly connector.

  1. Check if DTC 74-40 is output.

    OK:
    DTC 74-40 is not output.



NG
Go to step 15
OK


3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - SPEAKER)
  1. *1: for RH
  2. *2: for LH


  1. Disconnect the I19 stereo component amplifier assembly connector.


    E190036E01

  1. Disconnect the N2*1 and/or N8*2 rear No. 2 speaker assembly connector.

  1. Disconnect the I10*1 and/or I12*2 front No. 2 speaker assembly connector.

  1. Disconnect the O13 w/ box No. 1 speaker assembly connector.

  1. Disconnect the O37 quarter side speaker assembly*1 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I19-6 (WF1-) - O13-2 (WF1-)
    Always
    Below 1 Ω
    I19-1 (WF1+) - O13-1 (WF1+)
    Always
    Below 1 Ω
    I19-12 (RR-) - N2-1 (-TW)
    Always
    Below 1 Ω
    I19-5 (RR+) - N2-3 (+TW)
    Always
    Below 1 Ω
    I19-7 (SR-) - O37-2
    Always
    Below 1 Ω
    I19-2 (SR+) - O37-1
    Always
    Below 1 Ω
    I19-11 (RL-) - N8-1 (-TW)
    Always
    Below 1 Ω
    I19-4 (RL+) - N8-3 (+TW)
    Always
    Below 1 Ω
    I19-9 (FR-) - I10-4 (TWR-)
    Always
    Below 1 Ω
    I19-10 (FR+) - I10-3 (TWR+)
    Always
    Below 1 Ω
    I19-8 (FL-) - I12-4 (TWL-)
    Always
    Below 1 Ω
    I19-3 (FL+) - I12-3 (TWL+)
    Always
    Below 1 Ω
    I19-6 (WF1-) - Body ground
    Always
    10 kΩ or higher
    I19-1 (WF1+) - Body ground
    Always
    10 kΩ or higher
    I19-12 (RR-) - Body ground
    Always
    10 kΩ or higher
    I19-5 (RR+) - Body ground
    Always
    10 kΩ or higher
    I19-7 (SR-) - Body ground
    Always
    10 kΩ or higher
    I19-2 (SR+) - Body ground
    Always
    10 kΩ or higher
    I19-11 (RL-) - Body ground
    Always
    10 kΩ or higher
    I19-4 (RL+) - Body ground
    Always
    10 kΩ or higher
    I19-9 (FR-) - Body ground
    Always
    10 kΩ or higher
    I19-10 (FR+) - Body ground
    Always
    10 kΩ or higher
    I19-8 (FL-) - Body ground
    Always
    10 kΩ or higher
    I19-3 (FL+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (REAR NO. 1 SPEAKER - REAR NO. 2 SPEAKER)
  1. *1: for RH
  2. *2: for LH


    E190037E01
  1. Disconnect the N1*1 and/or N7*2 rear No. 1 speaker assembly connector.

  1. Disconnect the N2*1 and/or N8*2 rear No. 2 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    N1-2 - N2-2 (-)
    Always
    Below 1 Ω
    N1-1 - N2-4 (+)
    Always
    Below 1 Ω
    N1-2 - Body ground
    Always
    10 kΩ or higher
    N1-1 - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    N7-2 - N8-2 (-)
    Always
    Below 1 Ω
    N7-1 - N8-4 (+)
    Always
    Below 1 Ω
    N7-2 - Body ground
    Always
    10 kΩ or higher
    N7-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 3 SPEAKER)
  1. *1: for RH
  2. *2: for LH


    E190038E01
  1. Disconnect the I10*1 and/or I12*2 front No. 2 speaker assembly connector.

  1. Disconnect the L1*1 and/or M1*2 front No. 3 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    I10-2 (-) - L1-1
    Always
    Below 1 Ω
    I10-1 (+) - L1-3
    Always
    Below 1 Ω
    I10-2 (-) - Body ground
    Always
    10 kΩ or higher
    I10-1 (+) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    I12-2 (-) - M1-1
    Always
    Below 1 Ω
    I12-1 (+) - M1-3
    Always
    Below 1 Ω
    I12-2 (-) - Body ground
    Always
    10 kΩ or higher
    I12-1 (+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT REAR NO. 1 SPEAKER ASSEMBLY RH


    E144966
  1. Disconnect the N1 rear No. 1 speaker assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.8 to 2.6 Ω



NG
REPLACE REAR NO. 1 SPEAKER ASSEMBLY RH (Click here)
OK


7.INSPECT REAR NO. 2 SPEAKER ASSEMBLY RH


    E160614E23
  1. Disconnect the N2 rear No. 2 speaker assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (-TW) - 3 (+TW)
    Always
    3.0 to 4.2 Ω
    1 (-TW) - 2 (-)
    Always
    Below 1 Ω
    3 (+TW) - 4 (+)



NG
REPLACE REAR NO. 2 SPEAKER ASSEMBLY RH (Click here)
OK


8.INSPECT QUARTER SIDE SPEAKER ASSEMBLY RH
E160629
  1. Disconnect the O37 quarter side speaker assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.5 Ω



NG
REPLACE QUARTER SIDE SPEAKER ASSEMBLY RH (Click here)
OK


9.INSPECT REAR NO. 1 SPEAKER ASSEMBLY LH
E144966
  1. Disconnect the N7 rear No. 1 speaker assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.8 to 2.6 Ω



NG
REPLACE REAR NO. 1 SPEAKER ASSEMBLY LH (Click here)
OK


10.INSPECT REAR NO. 2 SPEAKER ASSEMBLY LH


    E160614E24
  1. Disconnect the N8 rear No. 2 speaker assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (-TW) - 3 (+TW)
    Always
    3.0 to 4.2 Ω
    1 (-TW) - 2 (-)
    Always
    Below 1 Ω
    3 (+TW) - 4 (+)



NG
REPLACE REAR NO. 2 SPEAKER ASSEMBLY LH (Click here)
OK


11.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY RH


    E160614
  1. Disconnect the L1 front No. 3 speaker assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Always
    3.0 to 4.2 Ω



NG
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY RH (Click here)
OK


12.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY RH


    E144969E29
  1. Disconnect the I10 front No. 2 speaker assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (TWR+) - 4 (TWR-)
    Always
    1.5 to 2.5 Ω
    2 (-) - 4 (TWR-)
    Always
    Below 1 Ω
    1 (+) - 3 (TWR+)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY RH (Click here)
OK


13.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY LH


    E160614
  1. Disconnect the M1 front No. 3 speaker assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Always
    3.0 to 4.2 Ω



NG
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY LH (Click here)
OK


14.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY LH


    E144969E30
  1. Disconnect the I12 front No. 2 speaker assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (TWL+) - 4 (TWL-)
    Always
    1.5 to 2.5 Ω
    2 (-) - 4 (TWL-)
    Always
    Below 1 Ω
    1 (+) - 3 (TWL+)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY LH (Click here)
OK

REPLACE W/ BOX NO. 1 SPEAKER ASSEMBLY (Click here)  

15.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - SPEAKER)
  1. *1: for RH
  2. *2: for LH


  1. Disconnect the I31 stereo component amplifier assembly connector.


    E190039E01

  1. Disconnect the L8*1 and M10*2 front No. 1 speaker assembly connectors.

  1. Disconnect the I14 front No. 4 speaker assembly connector.

  1. Disconnect the O13 w/ box No. 1 speaker assembly connector.

  1. Disconnect the O31*2 quarter side speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I31-9 (CTR-) - I14-2
    Always
    Below 1 Ω
    I31-3 (CTR+) - I14-1
    Always
    Below 1 Ω
    I31-10 (WF2-) - O13-4 (WF2-)
    Always
    Below 1 Ω
    I31-4 (WF2+) - O13-3 (WF2+)
    Always
    Below 1 Ω
    I31-6 (WFR-) - L8-2
    Always
    Below 1 Ω
    I31-2 (WFR+) - L8-1
    Always
    Below 1 Ω
    I31-5 (WFL-) - M10-2
    Always
    Below 1 Ω
    I31-1 (WFL+) - M10-1
    Always
    Below 1 Ω
    I31-7 (SL-) - O31-2
    Always
    Below 1 Ω
    I31-8 (SL+) - O31-1
    Always
    Below 1 Ω
    I31-9 (CTR-) - Body ground
    Always
    10 kΩ or higher
    I31-3 (CTR+) - Body ground
    Always
    10 kΩ or higher
    I31-10 (WF2-) - Body ground
    Always
    10 kΩ or higher
    I31-4 (WF2+) - Body ground
    Always
    10 kΩ or higher
    I31-6 (WFR-) - Body ground
    Always
    10 kΩ or higher
    I31-2 (WFR+) - Body ground
    Always
    10 kΩ or higher
    I31-5 (WFL-) - Body ground
    Always
    10 kΩ or higher
    I31-1 (WFL+) - Body ground
    Always
    10 kΩ or higher
    I31-7 (SL-) - Body ground
    Always
    10 kΩ or higher
    I31-8 (SL+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


16.INSPECT QUARTER SIDE SPEAKER ASSEMBLY LH


    E160629
  1. Disconnect the O31 quarter side speaker assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.5 Ω



NG
REPLACE QUARTER SIDE SPEAKER ASSEMBLY LH (Click here)
OK


17.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY RH


    E144966
  1. Disconnect the L8 front No. 1 speaker assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.8 to 2.6 Ω



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY RH (Click here)
OK


18.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY LH


    E144966
  1. Disconnect the M10 front No. 1 speaker assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.8 to 2.6 Ω



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY LH (Click here)
OK


19.INSPECT FRONT NO. 4 SPEAKER ASSEMBLY


    E146506
  1. Disconnect the I14 front No. 4 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω



NG
REPLACE FRONT NO. 4 SPEAKER ASSEMBLY (Click here)
OK

REPLACE W/ BOX NO. 1 SPEAKER ASSEMBLY (Click here)