Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM

WIPER AND WASHER SYSTEM > Wiper and Washer Switch Circuit

for Preparation Click here


DESCRIPTION

  1. The manual operation signals are sent to the main body ECU.
  2. Perform this inspection with the back door window glass fully closed.

WIRING DIAGRAM


E160104E01


INSPECTION PROCEDURE

1.CHECK VEHICLE CONDITION
  1. Check whether the rear wiper and washer systems operate normally.

Result 
Result
Proceed to
Rear wiper and washer systems do not operate.
A
Rear wiper system does not operate.
B
Rear washer system does not operate.
C


B
Go to step 8

C
Go to step 10
A


2.INSPECT FUSE (ECU-IG No. 2)


    B188612E06
  1. Remove the ECU-IG No. 2 fuse from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ECU-IG No. 2 fuse
    Always
    Below 1 Ω

  1. Reinstall the ECU-IG No. 2 fuse.



NG
REPLACE FUSE
OK


3.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY
E146708E06
  1. Remove the windshield wiper switch assembly.

  1. Inspect the rear wiper switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (EW) - 6 (C1R)
    Rear wiper switch OFF
    10 kΩ or higher
    2 (EW) - 7 (+1R)
    6 (C1R) -7 (+1R)
    2 (EW) - 6 (C1R)
    Rear wiper switch LO
    Below 1 Ω
    2 (EW) - 7 (+1R)
    Rear wiper switch HI
    Below 1 Ω

  1. Inspect the rear washer switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (EW) - 7 (+1R)
    Rear washer switch OFF
    10 kΩ or higher
    2 (EW) - 5 (WR)
    5 (WR) - 7 (+1R)
    2 (EW) - 5 (WR)
    Rear washer switch ON (Rear wiper switch in OFF position)
    Below 1 Ω
    2 (EW) - 7 (+1R)
    Rear washer switch ON (Rear wiper switch in ON position)
    Below 1 Ω
    2 (EW) - 5 (WR)
    5 (WR) - 7 (+1R)

  1. Reinstall the the windshield wiper switch assembly.



NG
REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH - BODY GROUND)


    E160105E01
  1. Disconnect the H14 windshield wiper switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H14-2 (EW) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the windshield wiper switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH - MAIN BODY ECU)


    E162504E01
  1. Disconnect the H3 and H4 main body ECU connector.

  1. Inspect the rear wiper switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H3-2 (RWIN) - Body ground
    Rear wiper switch OFF
    10 kΩ or higher
    H3-9 (RWON) - Body ground
    H3-2 (RWIN) - Body ground
    Rear wiper switch LO
    Below 1 Ω
    H3-9 (RWON) - Body ground
    Rear wiper switch HI
    Below 1 Ω
    H4-7 (RWSW) - Body ground
    Rear washer switch ON (Rear wiper switch in ON position)
    Below 1 Ω

  1. Inspect the rear washer switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H4-7 (RWSW) - Body ground
    Rear washer switch OFF
    10 kΩ or higher
    H4-7 (RWSW) - Body ground
    Rear washer switch ON (Rear wiper switch in ON position)
    Below 1 Ω
    Rear washer switch ON (Rear wiper switch in OFF position)
    Below 1 Ω

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (BATTERY - MAIN BODY ECU)


    E147142E02
  1. Disconnect the DA main body ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    DA-1 - Body ground
    Always
    11 to 14 V

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - IGNITION SWITCH, BODY GROUND)


    E162514E01
  1. Disconnect the DD main body ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    DD-43 - Body ground
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DD-62 - Body ground
    Always
    Below 1 Ω

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

8.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY
E146708E07
  1. Remove the windshield wiper switch assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (EW) - 6 (C1R)
    Rear wiper switch OFF
    10 kΩ or higher
    2 (EW) - 7 (+1R)
    6 (C1R) - 7 (+1R)
    2 (EW) - 6 (C1R)
    Rear wiper switch LO
    Below 1 Ω
    2 (EW) - 7 (+1R)
    Rear wiper switch HI
    Below 1 Ω

  1. Reinstall the windshield wiper switch assembly.



NG
REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH - MAIN BODY ECU, BODY GROUND)
E160107E01
  1. Disconnect the H3 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H3-2 (RWIN) - Body ground
    Rear wiper switch OFF
    10 kΩ or higher
    H3-9 (RWON) - Body ground
    H3-2 (RWIN) - Body ground
    Rear wiper switch LO
    Below 1 Ω
    H3-9 (RWON) - Body ground
    Rear wiper switch HI
    Below 1 Ω

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

10.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY
E146708E08
  1. Remove the windshield wiper switch assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (EW) - 7 (+1R)
    Rear washer switch OFF
    10 kΩ or higher
    2 (EW) - 5 (WR)
    5 (WR) - 7 (+1R)
    2 (EW) - 7 (+1R)
    Rear washer switch ON (Rear wiper switch in ON position)
    Below 1 Ω
    2 (EW) - 5 (WR)
    5 (WR) - 7 (+1R)

  1. Reinstall the windshield wiper switch assembly.



NG
REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY (Click here)
OK


11.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH - MAIN BODY ECU, BODY GROUND)
B136062E02
  1. Disconnect the H4 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H4-7 (RWSW) - Body ground
    Rear washer switch OFF
    10 kΩ or higher
    H4-7 (RWSW) - Body ground
    Rear washer switch ON (Rear wiper switch in ON position)
    Below 1 Ω
    Rear washer switch ON (Rear wiper switch in OFF position)
    Below 1 Ω

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)