DTC B2343 Position Initialization Incomplete |
| DTC Code | DTC Detection Condition | Trouble Area |
| B2343 | Sliding roof drive gear (sliding roof ECU) has not been initialized |
|

| 1.INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) |
Check that the sliding roof drive gear can be initialized (Click here).
|
| ||||
| OK | |
| 2.CHECK DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
| Result | Proceed to |
| No DTC is output | A |
| DTC B2343 is output | B |
|
| ||||
| A | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (ROOF CONSOLE BOX - SLIDING ROOF ECU AND BODY GROUND) |
![]() |
Disconnect the U3 ECU connector.
Disconnect the U7 roof console box connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| U7-3 (CLS) - U3-7 (CLS) | Always | Below 1 Ω |
| U7-3 (CLS) - Body ground | Always | 10 kΩ or higher |
| U7-4 (OPN) - U3-6 (OPN) | Always | Below 1 Ω |
| U7-4 (OPN) - Body ground | Always | 10 kΩ or higher |
| U7-5 (DOWN) - U3-2 (DWN) | Always | Below 1 Ω |
| U7-5 (DOWN) - Body ground | Always | 10 kΩ or higher |
| U7-6 (UP) - U3-1 (UP) | Always | Below 1 Ω |
| U7-6 (UP) - Body ground | Always | 10 kΩ or higher |
| U7-7 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.INSPECT SLIDING ROOF SWITCH |
![]() |
Remove the sliding roof switch (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 (UP) - 5 (E) | TILT switch is pressed to up | Below 1 Ω |
| TILT switch is not pressed to up | 10 kΩ or higher | |
| 2 (DOWN) - 5 (E) | TILT switch is pressed to down | Below 1 Ω |
| TILT switch is not pressed to down | 10 kΩ or higher | |
| 3 (CLS) - 5 (E) | SLIDE switch is pressed to close | Below 1 Ω |
| SLIDE switch is not pressed to close | 10 kΩ or higher | |
| 4 (OPN) - 5 (E) | SLIDE switch is pressed to open | Below 1 Ω |
| SLIDE switch is not pressed to open | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.INSPECT ROOF CONSOLE BOX ASSEMBLY |
![]() |
Remove the roof console box with sliding roof switch (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 3 (CLS) - 7 (E) | SLIDE switch is pressed to close | Below 1 Ω |
| SLIDE switch is not pressed to close | 10 kΩ or higher | |
| 4 (OPN) - 7 (E) | SLIDE switch is pressed to open | Below 1 Ω |
| SLIDE switch is not pressed to open | 10 kΩ or higher | |
| 5 (DOWN) - 7 (E) | TILT switch is pressed to down | Below 1 Ω |
| TILT switch is not pressed to down | 10 kΩ or higher | |
| 6 (UP) - 7 (E) | TILT switch is pressed to up | Below 1 Ω |
| TILT switch is not pressed to up | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||