Home › Drivetrain · A760F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

DTC    P2772    Four Wheel Drive (4WD) Low Switch Circuit Range / Performance

for Preparation Click here


DESCRIPTION

The ECM detects the signal from the transfer 4L position switch.
This DTC indicates that the transfer 4L position switch remains on.

DTC Code
DTC Detection Condition
Trouble Area
P2772
Transfer 4L position switch remains on while the vehicle is being driven under the following conditions for 1.8 sec. or more (1-trip detection logic):
(a) Output shaft speed is between 1000 and 3000 rpm.
(b) Transfer position switch is in 4H.
  1. Short in transfer 4L position switch circuit
  2. 4WD control ECU
  3. ECM

MONITOR DESCRIPTION

The ECM monitors the transfer-case 4L position switch to determine when the transfer-case 4L gears are engaged. If the transfer-case 4L gears remain engaged under the following conditions, the ECM will conclude that there is a malfunction of the 4L position switch, illuminate the MIL and store the DTC:
  1. The 4L switch indicates that the 4L transfer-case gears are engaged.
  2. The transfer-case shifter is in the "4H" position.
  3. The transfer-case output shaft speed is between 1000 and 3000 rpm.
  4. The specified time period has elapsed.

MONITOR STRATEGY


Related DTCs
P2772: Transfer 4L position switch/Functional check
Required sensors/Components
Transfer 4L position switch
Frequency of operation
Continuous
Duration
ON malfunction (A): 1.8 seconds
ON malfunction (B): 0.5 seconds
MIL operation
1 driving cycle
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not present
P0500 (Vehicle speed sensor "A" circuit)
Output speed sensor circuit
Not circuit malfunction
Transfer neutral position switch
OFF

ON Malfunction (A) 
Output speed (Transfer output speed)
1000 to 3000 rpm

ON Malfunction (B) 
Output speed (Transfer output speed)
143 rpm or more

TYPICAL MALFUNCTION THRESHOLDS

Both of the following conditions are met: ON malfunction (A) and (B)

ON Malfunction (A) 
4L switch
ON

ON Malfunction (B) 
Actual transfer gear ratio
Transfer input speed / Transfer output speed
0.9 or more, and less than 1.1

WIRING DIAGRAM

Refer to DTC P0818 .

INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

1.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - BODY GROUND)


    C209926E04
  1. Disconnect the A28 4WD control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A28-21 (L4) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to 4WD Control ECU)



NG
Go to step 2
OK

GO TO TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM (Click here)  

2.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - ECM)


    C197708E26
  1. Disconnect the A27 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A27-21 (L4) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)