Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1825/56    Short in Front Passenger Side - Side Squib Circuit

DTC    B1826/56    Open in Front Passenger Side - Side Squib Circuit

DTC    B1827/56    Short to GND in Front Passenger Side - Side Squib Circuit

DTC    B1828/56    Short to B+ in Front Passenger Side - Side Squib Circuit

for Preparation Click here


DESCRIPTION

The side squib RH circuit consists of the center airbag sensor and the front seat side airbag RH.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the side squib RH circuit.

DTC Code
Detection Condition
Trouble Area
B1825/56
When one of following conditions is met:
  1. The center airbag sensor receives a line short circuit signal 5 times in the side squib RH circuit during primary check.
  2. Side squib RH malfunction
  3. Center airbag sensor malfunction
  1. No. 2 floor wire
  2. Front seat side airbag assembly RH (Side squib RH)
  3. Center airbag sensor assembly
B1826/56
When one of following conditions is met:
  1. The center airbag sensor receives an open circuit signal in the side squib RH circuit for 2 seconds.
  2. Side squib RH malfunction
  3. Center airbag sensor malfunction
  1. No. 2 floor wire
  2. Front seat side airbag assembly RH (Side squib RH)
  3. Center airbag sensor assembly
B1827/56
When one of following conditions is met:
  1. The center airbag sensor receives a short circuit to ground signal in the side squib RH circuit for 0.5 seconds.
  2. Side squib RH malfunction
  3. Center airbag sensor malfunction
  1. No. 2 floor wire
  2. Front seat side airbag assembly RH (Side squib RH)
  3. Center airbag sensor assembly
B1828/56
When one of following conditions is met:
  1. The center airbag sensor receives a short circuit to B+ signal in the side squib RH circuit for 0.5 seconds.
  2. Side squib RH malfunction
  3. Center airbag sensor malfunction
  1. No. 2 floor wire
  2. Front seat side airbag assembly RH (Side squib RH)
  3. Center airbag sensor assembly

WIRING DIAGRAM


C180215E04


INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

HINT:
  1. Perform the simulation method by selecting "check mode" (signal check) with the Techstream (Click here).
  2. After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (Click here).

1.CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connector is properly connected to the front seat side airbag RH.

    OK:
    The connector is properly connected.

    HINT:
    If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

  1. Disconnect the connector from the front seat side airbag RH.

  1. Check that the terminal of the connector is not damaged.

    OK:
    The terminal is not deformed or damaged.



NG
REPLACE NO. 2 FLOOR WIRE
OK


2.CHECK FRONT SEAT SIDE AIRBAG RH (SIDE SQUIB RH)
C162329E03
  1. Connect the black wire side of SST (resistance: 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the front seat side airbag RH (side squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1825, B1826, B1827, B1828 or 56 is output
    A
    DTC B1825, B1826, B1827, B1828 or 56 is not output (w/ Manual Seat)
    B
    DTC B1825, B1826, B1827, B1828 or 56 is not output (w/ Power Seat)
    C

    HINT:
    Codes other than DTC B1825, B1826, B1827, B1828 and 56 may be output at this time, but they are not related to this check.



B
REPLACE FRONT SEAT ASSEMBLY RH (Click here)

C
REPLACE FRONT SEAT ASSEMBLY RH (Click here)
A


3.CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.

  1. Check that the connector is properly connected to the center airbag sensor assembly.

    OK:
    The connector is properly connected.

  1. Disconnect the connector from the center airbag sensor assembly.

  1. Check that the terminal of the connector is not damaged.

    OK:
    The terminal is not deformed or damaged.

  1. Check that the short spring for the No. 2 floor wire connector with the activation prevention mechanism is not deformed or damaged.

    OK:
    The short spring is not deformed or damaged.



NG
REPLACE NO. 2 FLOOR WIRE
OK


4.CHECK NO. 2 FLOOR WIRE (SIDE SQUIB RH CIRCUIT)
C180219E04
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    w/ Power Seat 
    Tester Connection
    Switch Condition
    Specified Condition
    P5-1 (SFR+) - Body ground
    Ignition switch ON
    Below 1 V
    P5-2 (SFR-) - Body ground
    Ignition switch ON
    Below 1 V
    w/o Power Seat 
    Tester Connection
    Switch Condition
    Specified Condition
    P16-1 (SFR+) - Body ground
    Ignition switch ON
    Below 1 V
    P16-2 (SFR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ Power Seat 
    Tester Connection
    Condition
    Specified Condition
    P5-1 (SFR+) - P5-2 (SFR-)
    Always
    Below 1 Ω
    w/o Power seat 
    Tester Connection
    Condition
    Specified Condition
    P16-1 (SFR+) - P16-2 (SFR-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ Power Seat 
    Tester Connection
    Condition
    Specified Condition
    P5-1 (SFR+) - P5-2 (SFR-)
    Always
    1 MΩ or higher
    P5-1 (SFR+) - Body ground
    Always
    1 MΩ or higher
    P5-2 (SFR-) - Body ground
    Always
    1 MΩ or higher
    w/o Power Seat 
    Tester Connection
    Condition
    Specified Condition
    P16-1 (SFR+) - P16-2 (SFR-)
    Always
    1 MΩ or higher
    P16-1 (SFR+) - Body ground
    Always
    1 MΩ or higher
    P16-2 (SFR-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE NO. 2 FLOOR WIRE
OK


5.CHECK CENTER AIRBAG SENSOR
C146261E11
  1. Restore the released activation prevention mechanism of connector B to the original condition.

  1. Connect the connectors to the front seat side airbag RH and the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1825, B1826, B1827, B1828 or 56 is not output.

    HINT:
    Codes other than DTC B1825, B1826, B1827, B1828 and 56 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)