DTC B1820/55 Short in Front Driver Side - Side Squib Circuit |
DTC B1821/55 Open in Front Driver Side - Side Squib Circuit |
DTC B1822/55 Short to GND in Front Driver Side - Side Squib Circuit |
DTC B1823/55 Short to B+ in Front Driver Side - Side Squib Circuit |
| DTC Code | Detection Condition | Trouble Area |
| B1820/55 | When one of following conditions is met:
|
|
| B1821/55 | When one of following conditions is met:
|
|
| B1822/55 | When one of following conditions is met:
|
|
| B1823/55 | When one of following conditions is met:
|
|

| 1.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connector is properly connected to the front seat side airbag LH.
Disconnect the connector from the front seat side airbag LH.
Check that the terminal of the connector is not damaged.
|
| ||||
| OK | |
| 2.CHECK FRONT SEAT SIDE AIRBAG LH (SEAT AIRBAG WIRE LH) |
![]() |
Connect the black wire side of SST (resistance: 2.1 Ω) to connector C.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1820, B1821, B1822, B1823 or 55 is output | A |
| DTC B1820, B1821, B1822, B1823 or 55 is not output (w/ Manual Seat) | B |
| DTC B1820, B1821, B1822, B1823 or 55 is not output (w/ Power Seat) | C |
|
| ||||
|
| ||||
| A | |
| 3.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector C.
Check that the connector is properly connected to the center airbag sensor assembly.
Disconnect the connector from the center airbag sensor assembly.
Check that the terminal of the connector is not damaged.
Check that the short spring for the floor wire connector with the activation prevention mechanism is not deformed or damaged.
|
| ||||
| OK | |
| 4.CHECK FLOOR WIRE (SIDE SQUIB LH CIRCUIT) |
![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O6-1 (SFL+) - Body ground | Ignition switch ON | Below 1 V |
| O6-2 (SFL-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O6-1 (SFL+) - O6-2 (SFL-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B .
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O6-1 (SFL+) - O6-2 (SFL-) | Always | 1 MΩ or higher |
| O6-1 (SFL+) - Body ground | Always | 1 MΩ or higher |
| O6-2 (SFL-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 5.CHECK CENTER AIRBAG SENSOR |
![]() |
Restore the released activation prevention mechanism of connector B to the original condition.
Connect the connectors to the front seat side airbag LH and the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||