CYLINDER HEAD GASKET > INSTALLATION |
| 1. INSPECT CYLINDER HEAD SET BOLT |
![]() |
Using a vernier caliper, measure the diameter of the elongated thread at the measuring point.
| 2. INSPECT CYLINDER HEAD LH |
![]() |
Using a precision straightedge and feeler gauge, measure the warpage of the surfaces where the cylinder head contacts the cylinder block and manifold.
| Item | Specified Condition |
| Cylinder block side | 0.05 mm (0.00197 in.) |
| Intake manifold side | 0.08 mm (0.00315 in.) |
| Exhaust manifold side | 0.05 mm (0.00197 in.) |
![]() |
Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.
If cracked, replace the cylinder head.
| 3. INSPECT CYLINDER HEAD SUB-ASSEMBLY |
![]() |
Using a precision straightedge and feeler gauge, measure the warpage of the surfaces where the cylinder head contacts the cylinder block and manifold.
| Item | Specified Condition |
| Cylinder block side | 0.05 mm (0.00197 in.) |
| Intake manifold side | 0.08 mm (0.00315 in.) |
| Exhaust manifold side | 0.05 mm (0.00197 in.) |
![]() |
Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.
If cracked, replace the cylinder head.
| 4. INSTALL NO. 2 CYLINDER HEAD GASKET |
Check the piston protrusions for each cylinder.
Clean the cylinder block with solvent.
Set the piston of the cylinder to be measured to slightly ATDC.
![]() |
Place the cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp upward.
| 5. INSTALL CYLINDER HEAD LH |
Place the cylinder head on the cylinder block.
Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.
![]() |
Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 10 cylinder head bolts with the plate washers in several steps, in the sequence shown in the illustration.
![]() |
Mark the front of the cylinder head bolts with paint.
Further tighten the cylinder head bolts 90° and then an additional 90° as shown in the illustration.
Check that the paint mark is now at a 180° angle from the front.
![]() |
Install and uniformly tighten the 2 cylinder head bolts.
| 6. INSTALL CYLINDER HEAD GASKET |
Check the piston protrusions for each cylinder.
Clean the cylinder block with solvent.
Set the piston of the cylinder to be measured to slightly ATDC.
![]() |
Place the cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp upward.
| 7. INSTALL CYLINDER HEAD SUB-ASSEMBLY |
Place the cylinder head on the cylinder block.
Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.
![]() |
Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 10 cylinder head bolts with the plate washers in several steps, in the sequence shown in the illustration.
![]() |
Mark the front of the cylinder head bolts with paint.
Further tighten the cylinder head bolts 90° and then an additional 90° as shown in the illustration.
Check that the paint mark is now at a 180° angle from the front.
![]() |
Install and uniformly tighten the 2 cylinder head bolts.
| 8. INSTALL VALVE STEM CAP |
Apply a light coat of engine oil to the valve stem caps.
Install the 32 valve stem caps to the cylinder head.
| 9. INSTALL VALVE LASH ADJUSTER ASSEMBLY |
Inspect the valve lash adjuster .
Install the 32 valve lash adjusters to the cylinder head.
| 10. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
Apply engine oil to the lash adjuster tips and valve stem cap ends.
![]() |
Install the 32 valve rocker arms as shown in the illustration.
| 11. INSTALL CAMSHAFTS |
Install the camshaft (Click here).
| 12. INSTALL EXHAUST MANIFOLD |
Install the exhaust manifold (Click here).