DTC P050B Cold Start Ignition Timing Performance |

| DTC No. | DTC Detection Condition | Trouble Area |
| P050B | Insufficient ignition timing retard at cold start (2 trip detection logic) |
|
| Related DTCs | P050B: Cold start ignition timing performance |
| Required Sensors/Components (Main) | Throttle body assembly |
| Required Sensors/Components (Related) | Mass air flow meter Engine Coolant Temperature (ECT) sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 10 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0010, P0020 (VVT oil control valve) P0011, P0021 (VVT system - Advance) P0012, P0022 (VVT system - Retard) P0013, P0023 (Exhaust VVT oil control valve) P0014, P0024 (Exhaust VVT system - Advance) P0015, P0025 (Exhaust VVT system - Retard) P0016, P0018 (VVT system - Misalignment) P0017, P0019 (Exhaust VVT system - Misalignment) P006A, P0107, P0108 (Manifold absolute pressure) P0102, P0103 (Mass air flow meter) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Front oxygen/Air fuel ratio sensor) P0171, P0172, P0174, P0175 (Fuel system) P0301 - P0308 (Misfire) P0335 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351 - P0358 (Igniter) P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor) P0500 (Vehicle speed sensor) P0401 (EGR system) P0452, P0453 (EVAP system) P0705 (Shift lever position switch) |
| Battery voltage | 8 V or more |
| Time after engine start | 3 seconds or more |
| Starter | OFF |
| ECT at engine start | -10°C (14°F) or more |
| ECT | -10 to 50°C (14 to 122°F) |
| Engine idling time | 3 seconds or more |
| Fuel-cut | OFF |
| Vehicle speed | Less than 3 km/h (1.875 mph) |
| Atmospheric pressure | 76 kPa (570 mmHg) or more |
| Accumulated time when ignition timing retard is cut off | 5 seconds or more |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Symptom | Factor | Trouble Area |
| Low idle speed when engine is cold (immediately after engine start) | Excessive engine friction |
|
| Rough idle when engine is cold (immediately after engine start) | Abnormal combustion | Fuel quality |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P050B) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTCs.
| Result | Proceed to |
| P050B is output | A |
| P050B and other are output | B |
|
| ||||
| A | |
| 2.READ VALUE USING TECHSTREAM (FUEL TRIM) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2.
Read the values displayed on the Techstream.
Add together the Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2 values to obtain the total fuel trim.
|
| ||||
| OK | |
| 3.INSPECT THROTTLE BODY ASSEMBLY (THROTTLE VALVE) |
Check for deposits around the throttle valve and check the throttle valve condition.
|
| ||||
| OK | |
| 4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION) |
Connect the Techstream to the DLC3.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.
Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition | Steady idling | Idling changes from steady to rough idling or engine stall |
| MAP (Data List) | 20 to 40 kPa (150 to 300 mmHg, 6 to 12 in.Hg) | MAP value is at least +10 kPa (75 mmHg, 3 in.Hg) higher than when EGR valve is fully closed |
|
| ||||
|
| ||||
| 5.INSPECT EGR VALVE |
Remove the EGR valve (Click here).
Check if the EGR valve is stuck open.
|
| ||||
|
| ||||
| 6.REPAIR OR REPLACE THROTTLE BODY ASSEMBLY |
Repair or replace the throttle body assembly (Click here).
|
| ||||
| 7.CHECK PCV HOSE |
Check the PCV hose connections .
|
| ||||
| OK | |
| 8.CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leaks .
|
| ||||
| OK | |
| 9.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Visually check that the air cleaner filter element sub-assembly is not excessively contaminated with dirt or oil.
|
| ||||
| OK | |
| 10.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION) |
Connect the Techstream to the DLC3.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.
Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition | Steady idling | Idling changes from steady to rough idling or engine stall |
| MAP (Data List) | 20 to 40 kPa (150 to 300 mmHg, 6 to 12 in.Hg) | MAP value is at least +10 kPa (75 mmHg, 3 in.Hg) higher than when EGR valve is fully closed |
|
| ||||
|
| ||||
| 11.INSPECT EGR VALVE |
Remove the EGR valve (Click here).
Check if the EGR valve is stuck open.
|
| ||||
| OK | |
| 12.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE VVT SYSTEM) |
Connect the Techstream to the DLC3.
Start the engine and turn the Techstream on.
Warm up the engine.
Turn the A/C on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2).
Check the engine speed while operating the camshaft oil control valve using the Techstream.
| Techstream Operation | Specified Condition |
| 0% | Normal engine speed |
| 100% | Engine idles roughly or stalls |
|
| ||||
| OK | |
| 13.READ VALUE USING TECHSTREAM (MAF) |
Connect the Techstream to the DLC3.
Start the engine and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 3000 rpm.
|
| ||||
|
| ||||
| 14.REPAIR OR REPLACE PCV HOSE |
Repair or replace the PCV hose.
|
| ||||
| 15.REPAIR OR REPLACE AIR INDUCTION SYSTEM |
Repair or replace the air induction system.
|
| ||||
| 16.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Replace the air cleaner filter element sub-assembly.
|
| ||||
| 17.REPLACE EGR VALVE |
Replace the EGR valve assembly (Click here).
|
| ||||
| 18.CHECK AND REPAIR VVT SYSTEM |
Check and repair the VVT system.
| NEXT | |
| 19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P050B.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P050B is output) | B |
|
| ||||
| A | ||
| ||
| 20.CHECK HARNESS AND CONNECTOR |
Check the connection and terminal and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (Click here).
| NEXT | |
| 21.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P050B.
Check the DTC judgment result.
| Result | Proceed to |
| ABNORMAL (DTC P050B is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | |
| 22.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D3-3 (VG) - D56-74 (VG) | Always | Below 1 Ω |
| D3-2 (E2G) - D56-75 (E2G) | Always | Below 1 Ω |
| D3-3 (VG) or D3-2 (E2G) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 23.REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter (Click here).
| NEXT | |
| 24.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P050B.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P050B is output) | B |
|
| ||||
| A | ||
| ||