Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING

ROOF HEADLINING > INSTALLATION

for Preparation Click here



1. INSTALL ROOF HEADLINING ASSEMBLY (w/o Rear Seat Entertainment System)


B193937
  1. Place the roof headlining into the cabin as shown in the illustration.

    NOTICE:
    Be careful not to damage the roof headlining when placing it in the cabin.

  1. Install the washer hose.



  1. Engage the clip and install the roof headlining.


    B193938



    B190136
  1. Install the visor holder with the screw.

    HINT:
    Use the same procedure to install the visor holder on the other side.

  1. Connect the satellite radio antenna connector.



    B190127
  1. Engage the 4 clamps to install the amplifier antenna.

  1. Install the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the connector.



    B190126
  1. Install the amplifier antenna with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the connector.



    B190163
  1. Install the washer hose and the amplifier antenna.

  1. Connect the connector.



    B190155
  1. Engage the 3 clamps to install the roof wire.

  1. Connect the connector.



2. INSTALL ROOF HEADLINING ASSEMBLY (w/ Rear Seat Entertainment System)


B193937
  1. Place the roof headlining into the cabin as shown in the illustration.

    NOTICE:
    Be careful not to damage the roof headlining when placing it in the cabin.

  1. Install the washer hose.



  1. Engage the clip and install the roof headlining.


    B193938



    B190136
  1. Install the visor holder with the screw.

    HINT:
    Use the same procedure to install the visor holder on the other side.



    B190127
  1. Engage the 4 clamps to install the amplifier antenna.

  1. Install the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the connector.



    B190126
  1. Install the amplifier antenna with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the connector.



    B190163
  1. Install the washer hose and the amplifier antenna.

  1. Connect the connector.



    B193939
  1. Engage the 3 clamps to install the roof wire.

  1. Connect the 2 connectors.



3. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)


B193936
  1. Place the roof headlining into the cabin as shown in the illustration.

    NOTICE:
    Be careful not to damage the roof headlining when placing it in the cabin.

  1. Install the washer hose.



  1. Engage the clip and 14 fasteners.


    B193935



    B190127
  1. Engage the 4 clamps to install the amplifier antenna.

  1. Install the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the connector.



    B190126
  1. Install the amplifier antenna with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the connector.



    B190163
  1. Install the washer hose and the amplifier antenna.

  1. Connect the connector.



    B191808
  1. Engage the 3 clamps to install the roof wire.

  1. Connect the 3 connectors.



4. INSTALL REAR VIEW INNER MIRROR STAY HOLDER COVER (w/ EC Mirror)


B227101
  1. Attach the 2 claws of the inner rear view mirror stay holder cover to the mirror, and then slide the inner rear view mirror stay holder cover in the direction indicated by the arrow in the illustration to attach the 2 claws to the roof headlining and install the inner rear view mirror stay holder cover.



5. INSTALL ROOF HEADLINING REAR TRIM COVER LH


B193893
  1. Engage the 6 claws to install the roof headlining rear trim cover LH.



6. INSTALL ASSIST GRIP PLUG


B165717
  1. Install a new assist grip plug.



7. INSTALL ASSIST GRIP SUB-ASSEMBLY


B169217

HINT:
Use the same procedure for the other 4 assist grips.

  1. Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.

  1. Install the assist grip.



8. INSTALL VISOR ASSEMBLY RH (w/ Illumination)


B191402
  1. Connect the connector.



    B190133
  1. Install the 4 screws and the visor.



9. INSTALL VISOR ASSEMBLY LH (w/ Illumination)

HINT:
Use the same procedure for both sides.



10. INSTALL VISOR ASSEMBLY RH (w/o Illumination)


B190135
  1. Install the visor with the 3 screws.



11. INSTALL VISOR ASSEMBLY LH (w/o Illumination)

HINT:
Use the same procedure for both sides.



12. INSTALL VISOR BRACKET COVER RH


B166262
  1. Attach the 4 claws to install the visor bracket cover.



13. INSTALL VISOR BRACKET COVER LH

HINT:
Use the same procedure for both sides.



14. INSTALL NO. 2 ROOM LIGHT ASSEMBLY
  1. Connect the connector.

  1. Engage the 2 claws to install the No. 2 room light.



  1. Engage the 2 claws to install the lens.


    B193063



15. INSTALL NO. 1 ROOM LIGHT ASSEMBLY
  1. Connect the connector.

  1. Engage the 4 clips to install the No. 1 room light.



  1. Engage the 4 claws to install the lens.


    B193921



16. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (w/ Rear Seat Entertainment System)


B191797
  1. Connect the connector.



    B193891
  1. Engage the 4 clips to install the No. 1 room light.



17. INSTALL ROOF CONSOLE BOX ASSEMBLY
  1. for Short Type:
    Install the roof console box .

  1. for Long Type:
    Install the roof console box .



18. INSTALL REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY RH


B190123
  1. Engage the 5 clips to install the rear window No. 2 side garnish assembly RH.

  1. Install the bolt.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    B193067
  1. Engage the claw to install the cover.



19. INSTALL REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY LH (w/o Power Back Door)

HINT:
Use the same procedure for both sides.



20. INSTALL REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY LH (w/ Power Back Door)


B191798
  1. Connect the connector.

  1. Engage the 5 clips to install the rear window No. 2 side garnish assembly LH.

  1. Install the bolt.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    B193892
  1. Engage the claw to install the cover.



21. INSTALL REAR WINDOW SIDE GARNISH ASSEMBLY RH


B190124
  1. Pass the rear seat outer belt floor anchor through the quarter trim panel.

  1. Engage the 5 clips to install the rear window side garnish.

  1. Install the bolt.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    B193066
  1. Engage the claw to install the cover.



22. INSTALL REAR WINDOW SIDE GARNISH ASSEMBLY LH

HINT:
Use the same procedure for both sides.



23. INSTALL QUARTER TRIM PANEL ASSEMBLY RH
  1. Connect the connector.

  1. Engage the 11 clips to install the quarter trim panel assembly.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



  1. Install the 2 clips.


    B219907



    B190147
  1. Engage the 2 claws to install the cover.



    B190146
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190158
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190145
  1. Engage the 3 claws to install the outer lap belt anchor cover.



24. INSTALL QUARTER TRIM PANEL ASSEMBLY LH
  1. Connect the connector.

  1. Engage the 11 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



  1. Install the 2 clips.


    B222458



    B193068
  1. Engage the 2 claws to install the cover.



    B191816
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B191818
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B193920
  1. Engage the 3 claws to install the outer lap belt anchor cover.



25. INSTALL QUARTER TRIM PANEL ASSEMBLY RH (for Power Seat)
  1. Connect the 3 connectors.

  1. Engage the 11 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



  1. Install the 2 clips.


    B222459



    B190147
  1. Engage the 2 claws to install the cover.



    B190146
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190158
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190145
  1. Engage the 3 claws to install the outer lap belt anchor cover.



26. INSTALL QUARTER TRIM PANEL ASSEMBLY LH (for Power Seat)
  1. Connect the 5 connectors.

  1. Engage the 12 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Engage the 2 clamps to install the wire harness.



  1. Install the 2 clips.


    B222460



    B193068
  1. Engage the 2 claws to install the cover.



    B191816
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B191818
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B193920
  1. Engage the 3 claws to install the outer lap belt anchor cover.



27. INSTALL REAR FLOOR MAT SUPPORT PLATE


B190142
  1. Engage the 5 clips to the 4 claws, and install the rear floor mat support plate.



28. INSTALL ROPE HOOK ASSEMBLY


B190141
  1. Install the rope hook with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B190139
  1. Engage the 2 claws to install the cover.



29. INSTALL CENTER PILLAR GARNISH RH
  1. Pass the front seat outer belt floor anchor through the center pillar garnish.

  1. Engage the clip and the guide to install the center pillar garnish.

  1. Install the bolt.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Install the assist grip with the 2 bolts.

    Torque:
    9.7 N*m{ 99 kgf*cm , 86 in.*lbf }



  1. Engage the 2 claws to install the 2 assist grip plugs.


    B193061



30. INSTALL CENTER PILLAR GARNISH LH

HINT:
Use the same procedure for both sides.



31. INSTALL LOWER CENTER PILLAR GARNISH RH


B190125
  1. Engage the 7 clips and 2 claws to install the center pillar garnish.



    B190129
  1. Install the front seat outer belt assembly RH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190128
  1. Engage the 3 claws to install the cover.



32. INSTALL LOWER CENTER PILLAR GARNISH LH

HINT:
Use the same procedure for both sides.



33. INSTALL FRONT PILLAR GARNISH RH


B190132E01
  1. Remove the protective cover.

  1. Engage the claw to install the front pillar garnish.

  1. Install the assist grip with the 2 bolts.

    Torque:
    9.7 N*m{ 99 kgf*cm , 86 in.*lbf }



  1. Engage the 2 claws to install the 2 assist grip plugs.


    B193062



34. INSTALL FRONT PILLAR GARNISH LH

HINT:
Use the same procedure for both sides.



35. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


B190154E01
  1. Align the location mark with the paint mark first, and install the rear door opening trim weatherstrip, as shown in the illustration.
    Paint Mark 
    Area
    Color
    RH side
    Pink
    LH side
    Purple



36. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure for both sides.



37. INSTALL REAR DOOR SCUFF PLATE RH


B186666
  1. Engage the 2 claws and 5 clips to install the rear door scuff plate.

  1. Install the 2 bolts.



    B186665
  1. Engage the 6 claws, 5 clips and 2 guides to install the rear door scuff plate.

  1. Install the screw.



38. INSTALL REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



39. INSTALL REAR FLOOR STEP NO. 1 COVER


B191404
  1. Engage the 2 claws to install the rear floor step No. 1 cover.



40. INSTALL REAR FLOOR STEP NO. 2 COVER


B193890
  1. Engage the 2 claws to install the rear floor step No. 2 cover.



41. INSTALL REAR SEAT CUSHION HINGE LOWER COVER RH


B191794
  1. Engage the 2 clips and 5 claws to install the rear cushion hinge lower cover RH.



42. INSTALL REAR SEAT CUSHION HINGE LOWER COVER LH

HINT:
Use the same procedure for both sides.



43. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


B190153E01
  1. Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.
    Paint Mark 
    Area
    Color
    RH side
    White
    LH side
    Yellow



44. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure for both sides.



45. INSTALL COWL SIDE TRIM BOARD RH


B190152
  1. Engage the 2 clips to install the cowl side trim board.

  1. Install the clip.



46. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure for both sides.



47. INSTALL FRONT DOOR SCUFF PLATE RH


B190151
  1. Engage the 9 claws to install the scuff plate.



48. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



49. INSTALL REAR NO. 2 SEAT ASSEMBLY RH
  1. for Manual Seat:
    Install the rear No. 2 seat assembly RH .

  1. for Power Seat:
    Install the rear No. 2 seat assembly RH .



50. INSTALL REAR NO. 2 SEAT ASSEMBLY LH
  1. for Manual Seat:
    Install the rear No. 2 seat assembly LH .

  1. for Power Seat:
    Install the rear No. 2 seat assembly LH .



51. INSTALL DECK BOARD BRACKET


B190119
  1. Install the deck board bracket with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



52. INSTALL DECK BOARD REINFORCEMENT SUB-ASSEMBLY


B190120
  1. Install the deck board reinforcement with the 4 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



53. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY


B190117
  1. Engage the 5 clips to install the No. 1 deck board.



54. INSTALL ROPE HOOK ASSEMBLY


B191405
  1. Install the rope hook with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    HINT:
    Use the same procedure for both sides.



55. INSTALL LUGGAGE COMPARTMENT TRIM BOX


B190116
  1. Install the luggage compartment trim box with the 4 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    B194633
  1. Install the 4 caps.



56. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


B194608
  1. Engage the 4 guides to install the No. 2 deck board.



57. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



58. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).