Home › Engine / Hybrid System ยท 1UR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P060B    Internal Control Module A/D Processing Performance

for Preparation Click here


DESCRIPTION

This DTC is output when a communication error occurs in the ECM.

DTC No.
DTC Detection Condition
Trouble Area
P060B
ECM main CPU communication error
(1 trip detection logic)
  1. ECM
  2. Knock sensor

MONITOR STRATEGY


Related DTCs
None
Required sensors/Components (Main)
ECM
Required sensors/Components (Related)
-
Frequency of operation
Once per driving cycle
Duration
16 seconds
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None

TYPICAL MALFUNCTION THRESHOLDS


When one of following conditions is met
Condition 1, 2, 3 or 4
1. Internal control module serial communication
Fail
2. AD converter
Fail
3. Knock sensor circuit
Fail
4. Knock sensor serial communication
Fail

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
  4. Turn the Techstream off.
  5. Turn the ignition switch off.
  6. Disconnect the Techstream.
  7. Disconnect the cable from the negative (-) battery terminal land wait for 1 minutes.
  8. Connect the cable to the negative (-) battery terminal.
  9. Connect the Techstream to the DLC3.
  10. Turn the ignition switch to ON and turn the Techstream on.
  11. Wait 16 seconds or more.
  12. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  13. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  14. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  15. Input the DTC: P060B.
  16. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  17. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the Techstream off.

  1. Turn the ignition switch off.

  1. Disconnect the Techstream.

  1. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Wait 16 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Check for DTCs.
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P060B is output
    B
    DTC P060B and P0327, P0328, P032C, P032D, P0332, P0333, P033C or P033D are output
    C



B
REPLACE ECM (Click here)

C
GO TO DTC (P0327, P0328, P032C, P032D, P0332, P0333, P033C OR P033D) (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)