REAR DOOR > DISASSEMBLY |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE REAR DOOR FRAME GARNISH |
![]() |
Disengage the 6 clips and remove the rear door frame garnish.
| 4. REMOVE REAR DOOR ARMREST BASE UPPER PANEL |
![]() |
Disengage the 2 clips and 5 claws and remove the rear door armrest base upper panel.
| 5. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Using a moulding remover, disengage the 4 claws and remove the rear door inside handle bezel plug.
| 6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Remove the rear door armrest cover.
Remove the 2 screws.
![]() |
Disengage the 9 clips.
Disconnect the connector.
![]() |
Disconnect the rear door lock remote control cable and the rear door inside locking cable and remove the rear door trim board sub-assembly.
| 7. REMOVE REAR DOOR INSIDE HANDLE BEZEL |
![]() |
Remove the 4 screws and remove the rear door inside handle bezel.
| 8. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY |
![]() |
Remove the 3 screws and remove the rear door inside handle sub-assembly.
| 9. REMOVE REAR DOOR GLASS INNER WEATHERSTRIP |
![]() |
Raise the 8 claws of the rear door glass inner weatherstrip and then remove the rear door glass inner weatherstrip from the rear door trim board sub-assembly, as shown in the illustration.
| 10. REMOVE REAR NO. 1 SPEAKER ASSEMBLY |
![]() |
Disconnect the speaker connector.
Remove the 3 screws.
![]() |
Disengage the 2 claws and remove the speaker.
| 11. REMOVE REAR DOOR TRIM NO. 2 BRACKET |
![]() |
Remove the 2 screws and remove the rear door trim No. 2 bracket.
| 12. REMOVE REAR DOOR SERVICE HOLE COVER |
![]() |
Disengage the clamps and disconnect the connectors.
![]() |
Remove the rear door service hole cover.
| 13. REMOVE REAR DOOR WINDOW FRAME REAR MOULDING |
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
| Rear Door Window Frame Rear Moulding | 20 to 30°C (68 to 86°F) |
![]() |
Put protective tape around the rear door window frame rear moulding.
Using a moulding remover, detach the 2 clips and remove the double-sided tape to remove the rear door window frame rear moulding.
| 14. REMOVE REAR DOOR GLASS OUTER WEATHERSTRIP |
![]() |
Apply protective tape to the door panel in the area around the rear door glass outer weatherstrip.
![]() |
Using a moulding remover, disengage the 5 claws and the clip and remove the rear door glass outer weatherstrip.
| 15. REMOVE REAR DOOR GLASS RUN |
![]() |
Remove the rear door glass run.
| 16. REMOVE REAR DOOR FRAME BRACKET |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 rear door frame bracket.
| 17. REMOVE REAR DOOR WINDOW FRAME REAR LOWER SUB-ASSEMBLY |
![]() |
Loosen nut A.
Remove the 3 bolts and remove the rear door window frame rear lower sub-assembly.
| 18. REMOVE REAR DOOR WINDOW GUIDE FRONT SUB-ASSEMBLY |
![]() |
Remove the 2 bolts and remove rear door window guide front sub-assembly.
| 19. REMOVE REAR DOOR GLASS SUB-ASSEMBLY |
![]() |
Provisionally install the power window switch.
Move the rear door glass until the 2 bolts can be seen through the service holes.
Remove the 2 bolts and remove the rear door glass sub-assembly.
| 20. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY |
![]() |
Disconnect the connector.
Loosen bolt A.
Remove the 5 bolts and remove the rear door window regulator sub-assembly.
| 21. REMOVE REAR DOOR CHECK ASSEMBLY |
![]() |
Remove the bolt and 2 nuts.
Remove the rear door check assembly.
| 22. REMOVE REAR DOOR WEATHERSTRIP |
![]() |
Disengage the 42 clips and remove the rear door weatherstrip.
| 23. REMOVE REAR DOOR NO. 2 WEATHERSTRIP |
![]() |
Disengage the 17 clips and remove rear door No. 2 weatherstrip.
| 24. REMOVE REAR DOOR LOCK |
![]() |
Using a "TORX" socket wrench T30, remove the 3 screws.
Move the rear door lock downward and pull the release plate out of the rear door outside handle frame.
Remove the door lock wire harness seal from the rear door lock.
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
![]() |
Remove the rear door lock remote control cable.
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and open the cover.
![]() |
Remove the rear door inside locking cable.
| 25. REMOVE REAR DOOR OUTSIDE HANDLE COVER |
![]() |
Using "TORX" socket wrench T30, remove the screw and the rear door outside handle cover.
| 26. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY |
![]() |
Remove the rear door outside handle assembly by sliding and pulling it in the direction indicated by the arrow mark in the illustration.
| 27. REMOVE REAR DOOR OUTSIDE HANDLE REAR PAD |
![]() |
Disengage the 2 claws and remove the rear door outside handle rear pad.
| 28. REMOVE REAR DOOR OUTSIDE HANDLE FRONT PAD |
![]() |
Disengage the 2 claws and remove the rear door outside handle front pad.
| 29. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY |
![]() |
Using "TORX" socket wrench T30, loosen the screw.
Disengage the claw and slide the rear door outside handle frame sub-assembly to remove it.
| 30. REMOVE CUSHION |
![]() |
Remove the cushions from the door panel.