Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Turn Signal Light Circuit

for Preparation Click here


DESCRIPTION

The turn signal flasher receives a turn signal switch signal from the headlight dimmer switch, and illuminates the front turn signal light, outer rear view mirror and rear combination light.

WIRING DIAGRAM


E161598E02


INSPECTION PROCEDURE

1.CHECK TURN SIGNAL LIGHT
  1. Check that the turn signal lights blink.

    Result 
    Result
    Proceed to
    All turn signal lights do not blink
    A
    Only front turn signal light does not blink
    B
    Only rear combination light does not blink
    C
    Only door mirror foot light does not blink*
    D

    1. *: w/ Side turn signal light.



B
Go to step 4

C
Go to step 6

D
Go to step 8
A


2.INSPECT FUSE (LH-IG, TURN-HAZ)


    E176441E01
  1. Remove the LH-IG fuse from the main body ECU.

  1. Remove the TURN-HAZ fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    LH-IG fuse
    Always
    Below 1 Ω
    TURN-HAZ fuse
    Always
    Below 1 Ω

  1. Reinstall the LH-IG and TURN-HAZ fuses.



NG
REPLACE FUSE
OK


3.CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER - BATTERY, IGNITION SWITCH, BODY GROUND)


    E147627E02
  1. Disconnect the H39 turn signal flasher assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H39-3 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    H39-1 (B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H39-4 (E) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the turn signal flasher assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

4.INSPECT FRONT TURN SIGNAL LIGHT BULB
  1. Temporarily replace the front turn signal light bulb with a new or normally functioning one .

  1. Check that the front turn signal light turn on.

    OK:
    Front turn signal light turn on



NG
Go to step 5
OK

END 

5.CHECK HARNESS AND CONNECTOR (FRONT TURN SIGNAL LIGHT - TURN SIGNAL FLASHER, BODY GROUND)
E146104E03
  1. for LH:

    1. Disconnect the A15 Front turn signal light LH connector.

    2. Disconnect the H39 turn signal flasher assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A15-3 (B) - H39-10 (LTRN)
      Always
      Below 1 Ω
      A15-2 (E) - Body ground
      Always
      Below 1 Ω
      A15-3 (B) - Body ground
      Always
      10 kΩ or higher

    4. Reconnect the turn signal flasher assembly connector.

    5. Reconnect the Front turn signal light LH connector.

  1. for RH:

    1. Disconnect the A16 Front turn signal light RH connector.

    2. Disconnect the H39 turn signal flasher assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A16-3 (B) - H39-17 (RTRN)
      Always
      Below 1 Ω
      A16-2 (E) - Body ground
      Always
      Below 1 Ω
      A16-3 (B) - Body ground
      Always
      10 kΩ or higher

    4. Reconnect the turn signal flasher assembly connector.

    5. Reconnect the Front turn signal light RH connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TURN SIGNAL FLASHER ASSEMBLY (Click here)  

6.INSPECT REAR TURN SIGNAL LIGHT BULB
  1. Temporarily replace the rear turn signal light bulb with a new or normally functioning one .

  1. Check that the rear turn signal light turn on.

    OK:
    Rear turn signal light turn on.



NG
Go to step 7
OK

END 

7.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT - TURN SIGNAL FLASHER, BODY GROUND)
E161600E02
  1. for LH:

    1. Disconnect the O23 rear combination light assembly LH connector.

    2. Disconnect the H39 turn signal flasher assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O23-1 (TRN) - H39-2 (LL)
      Always
      Below 1 Ω
      O23-2 (E) - Body ground
      Always
      Below 1 Ω
      O23-1 (TRN) - Body ground
      Always
      10 kΩ or higher

    4. Reconnect the turn signal flasher assembly connector.

    5. Reconnect the rear combination light assembly LH connector.

  1. for RH:

    1. Disconnect the O22 rear combination light assembly RH connector.

    2. Disconnect the H39 turn signal flasher assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O22-1 (TRN) - H39-8 (LR)
      Always
      Below 1 Ω
      O22-2 (E) - Body ground
      Always
      Below 1 Ω
      O22-1 (TRN) - Body ground
      Always
      10 kΩ or higher

    4. Reconnect the turn signal flasher assembly connector.

    5. Reconnect the rear combination light assembly RH connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TURN SIGNAL FLASHER ASSEMBLY (Click here)  

8.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY
E161601E01
  1. Remove the outer rear view mirror assembly (Click here).

  1. Apply battery voltage to the terminals and check that the side turn signal light turn on.

    OK:
    Tester Connection
    Specified Condition
    Positive battery (+) → 4 (B)
    Negative battery (-) → 3 (E)
    Side turn signal light turn on.

  1. Reinstall the outer rear view mirror assembly.



NG
Go to step 10
OK


9.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR - TURN SIGNAL FLASHER, BODY GROUND)
E147742E03
  1. for LH:

    1. Disconnect the M5 outer rear view mirror assembly LH connector.

    2. Disconnect the H39 turn signal flasher assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      M5-4 (B) - H39-2 (LL)
      Always
      Below 1 Ω
      M5-3 (E) - Body ground
      Always
      Below 1 Ω
      M5-4 (B) - Body ground
      Always
      10 kΩ or higher

    4. Reconnect the turn signal flasher assembly connector.

    5. Reconnect the outer rear view mirror assembly LH connector.

  1. for RH:

    1. Disconnect the L6 outer rear view mirror assembly RH connector.

    2. Disconnect the H39 turn signal flasher assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L6-4 (B) - H39-8 (LR)
      Always
      Below 1 Ω
      L6-3 (E) - Body ground
      Always
      Below 1 Ω
      L6-4 (B) - Body ground
      Always
      10 kΩ or higher

    4. Reconnect the turn signal flasher assembly connector.

    5. Reconnect the outer rear view mirror assembly RH connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY - BODY GROUND) 

10.INSPECT OUTER REAR VIEW MIRROR SUB-ASSEMBLY
  1. Temporarily replace the outer rear view mirror sub assembly with a new or normally functioning one (Click here).

  1. Check that the side turn signal light turn on.

    OK:
    Side turn signal light turn on.



NG
REPAIR OR REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (Click here)
OK

END