Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK

FRONT DOOR LOCK > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedure listed below is the LH side.



1. INSTALL FRONT DOOR LOCK

NOTICE:
  1. If reusing a door lock that has been removed, replace the packing in the connecting part with new packing.
  2. Make sure that no grease or dirt adheres to the packing surface in the connecting part.

  1. Apply MP grease to the sliding and rotating areas of the front door lock.



    B192554
  1. Install the front door inside locking cable.



    B192553
  1. Engage the 3 claws and close the cover.



    B192551
  1. Install the front door lock remote control cable.

  1. Install a new door lock wire harness seal on to the front door lock.

  1. Insert the front door lock open rod into the front door lock, and set it to the front door outside handle frame.

  1. Make sure that the front door lock open rod is securely connected to the front door lock.

  1. Apply adhesive to the threads of the screws.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



    B190561
  1. Using a "TORX" socket wrench T30, install the front door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



2. INSTALL FRONT DOOR FRAME REAR LOWER SUB-ASSEMBLY


    B190556
  1. Install the front door frame rear lower sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY


    B192559
  1. Insert the door glass into the door panel by the arrows in the illustration.

    NOTICE:
    Do not damage the glass.



    B190553
  1. Install the front door glass onto the front door window regulator with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



4. INSTALL FRONT DOOR GLASS RUN


    B190552
  1. Install the front door glass run.



5. INSTALL FRONT DOOR SERVICE HOLE COVER


    B195024
  1. Apply butyl tape to the door panel, then install a new front door service hole cover as shown in the illustration.

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.



    B190551
  1. Engage the clamps and connect the connectors.



6. INSTALL FRONT DOOR TRIM NO. 1 BRACKET


    B190549
  1. Install the front door No. 1 trim bracket with the 2 screws.



7. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
  1. Connect the connectors.



    B190543
  1. Connect the front door lock remote control cable and the front door inside locking cable.



    B190542
  1. Engage the 10 clips and install the front door trim board sub-assembly.



    B190541
  1. Tighten the 2 screws.

  1. Install the front door armrest cover.



8. INSTALL FRONT ARMREST BASE UPPER PANEL


B190537
  1. Connect the connector.

  1. Engage the 2 clips and 5 claws and install the front armrest base upper panel.



9. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    B190540
  1. Engage the 4 claws and install the front door inside handle bezel plug



10. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH


B194240
  1. Engage the 3 clips and install the front door lower frame bracket garnish.



11. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH (for 14 Speakers)


B190538
  1. Connect the connector.

  1. Engage the 3 clips and install the front door lower frame bracket garnish.



12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



13. INSPECT SRS WARNING LIGHT
(Click here)