Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)

STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column) > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).



1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


2. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



3. CUSTOMIZE INFORMATION
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Utility / Customize Setting / Tilt & Telescopic.

  1. Turn the auto away/return function OFF.

  1. Turn the ignition switch to ACC.

  1. Operate the tilt and telescopic switch to fully raise the tilt and extend the steering wheel.

  1. Turn the ignition switch OFF.



4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).



5. REMOVE LOWER NO. 3 STEERING WHEEL COVER


    B166432
  1. Using a screwdriver, remove the steering wheel cover.

    HINT:
    Tape the screwdriver tip before use.



6. REMOVE LOWER NO. 2 STEERING WHEEL COVER


    B166433
  1. Using a screwdriver, remove the No. 2 steering wheel cover.

    HINT:
    Tape the screwdriver tip before use.



7. REMOVE STEERING PAD


    C180934
  1. Using a T30 "TORX" socket wrench, loosen the 2 screws until the groove along the screw circumference catches on the screw case.

  1. Pull the steering pad toward you.



    B166581
  1. Using a thin-bladed screwdriver, release the locking button.

  1. Using a thin-bladed screwdriver, disconnect the 2 connectors.

  1. Detach the horn terminal.



8. REMOVE STEERING WHEEL ASSEMBLY


    C180956
  1. Detach the cruise control main wire harness clamp from the steering wheel side.

  1. Disconnect the steering pad switch connector and cruise control main switch connector from the spiral cable.

  1. Remove the steering wheel set nut.



    C180950E01
  1. Put matchmarks on the steering wheel and main shaft.

  1. Using SST, remove the steering wheel.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05011)



9. REMOVE LOWER STEERING COLUMN COVER


C181134
  1. Remove the 2 screws.

  1. Detach the 2 claws to remove the lower steering column cover.



10. REMOVE UPPER STEERING COLUMN COVER


    C159215
  1. Detach the 4 clips.

  1. Detach the claw to remove the upper steering column cover.



11. REMOVE TILT AND TELESCOPIC MANUAL SWITCH


C159804
  1. Disconnect the connector.

  1. Using a screwdriver, detach the claw and pull out the tilt and telescopic switch.

    NOTICE:
    Pushing on the claw too hard will break the claw.

    HINT:
    Tape the screwdriver tip before use.



12. REMOVE COMBINATION SWITCH WITH SPIRAL CABLE


C180951
  1. Disconnect the all connectors from the combination switch with spiral cable.



    C159216E01
  1. Using pliers, grip the claws of the clamp and remove the combination switch with spiral cable from the steering column.



13. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



14. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure for both sides.



15. REMOVE INSTRUMENT SIDE PANEL LH


    B226739
  1. Using a moulding remover, detach the 7 claws and remove the side panel.



16. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


    B229064
  1. Remove the 2 bolts.

  1. Detach the 9 clips and claw.



    B163883
  1. Detach the 2 claws and remove the sensor.

  1. Remove the finish panel and then disconnect the connectors.



17. REMOVE LOWER NO.1 INSTRUMENT PANEL AIR BAG ASSEMBLY


    B225997
  1. Remove the 4 bolts and remove the instrument panel airbag.

  1. Detach the 2 claws and disconnect the DLC3.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



18. REMOVE NO. 3 AIR DUCT SUB-ASSEMBLY


C154523
  1. Remove the bolt and air duct.



19. REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY


    C155149
  1. Remove the 3 bolts and nut.



    C154524E01
  1. Put matchmarks on the steering intermediate shaft and the steering column.

  1. Remove the bolt and steering intermediate shaft from the steering column.



    C155150E01
  1. Put matchmarks on the No. 2 steering intermediate shaft and steering intermediate shaft.

  1. Remove the bolt.

  1. Separate the steering intermediate shaft from the No. 2 steering intermediate shaft.



20. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


C155151E01
  1. Put matchmarks on the No. 2 steering intermediate shaft and power steering gear.

  1. Remove the bolt and No. 2 steering intermediate shaft from the power steering gear.



21. REMOVE STEERING COLUMN ASSEMBLY


    C159218
  1. Disconnect the connectors and disengage the wire.

  1. Remove the bolt and 2 nuts. Then remove the steering column from the instrument panel reinforcement.