SFI SYSTEM > Fuel Pump Control Circuit |

| 1.PERFORM ACTIVE TEST USING TECHSTREAM (FUEL PUMP) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check whether operating sounds can be heard while operating the relay using the Techstream.
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM AND BODY GROUND) |
![]() |
Disconnect the O35 fuel pump ECU connector.
Disconnect the A27 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O35-1 (FPC) - A27-52 (FPC) | Always | Below 1 Ω |
| O35-2 (DI) - A27-18 (DI) | Always | Below 1 Ω |
| O35-3 (E) - Body ground | Always | Below 1 Ω |
| O35-1 (FPC) or A27-52 (FPC) - Body ground | Always | 10 kΩ or more |
| O35-2 (DI) or A27-18 (DI) - Body ground | Always | 10 kΩ or more |
|
| ||||
| OK | |
| 3.REPLACE FUEL PUMP ECU |
Replace the fuel pump ECU (Click here).
| NEXT | |
| 4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Check the fuel pump operation.
|
| ||||
| OK | ||
| ||
| 5.INSPECT CIRCUIT OPENING RELAY (C/OPN) |
![]() |
Remove the circuit opening relay (C/OPN) from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | When no battery voltage applied to terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | When battery voltage applied to terminals 1 and 2 | Below 1 Ω |
|
| ||||
| OK | |
| 6.INSPECT CIRCUIT OPENING RELAY (POWER SOURCE VOLTAGE) |
![]() |
Remove the circuit opening relay (C/OPN) from the engine room relay block.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C/OPN relay (1) - Body ground | Ignition switch ON | 11 to 14 V |
| C/OPN relay (3) - Body ground | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY - ECM AND FUEL PUMP ECU) |
![]() |
Remove the circuit opening relay (C/OPN) from the engine room relay block.
Disconnect the A27 ECM connector.
Disconnect the O35 fuel pump ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C/OPN relay (1) - A27-48 (FC) | Always | Below 1 Ω |
| C/OPN relay (3) - O35-4 (+B) | Always | Below 1 Ω |
| C/OPN relay (1) or A27-48 (FC) - Body ground | Always | 10 kΩ or higher |
| C/OPN relay (3) or O35-4 (+B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU) |
![]() |
Disconnect the Q1 fuel pump connector.
Disconnect the O36 fuel pump ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Q1-4 (B2) - O36-1 (FP) | Always | Below 1 Ω |
| Q1-5 (E2) - O36-2 (FP-) | Always | Below 1 Ω |
| Q1-4 (B2) or O36-1 (FP) - Body ground | Always | 10 kΩ or higher |
| Q1-5 (E2) or O36-2 (FP-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.INSPECT FUEL PUMP |
Inspect the fuel pump (Click here).
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM AND BODY GROUND) |
![]() |
Disconnect the O35 fuel pump ECU connector.
Disconnect the A27 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O35-1 (FPC) - A27-52 (FPC) | Always | Below 1 Ω |
| O35-2 (DI) - A27-18 (DI) | Always | Below 1 Ω |
| O35-3 (E) - Body ground | Always | Below 1 Ω |
| O35-1 (FPC) or A27-52 (FPC) - Body ground | Always | 10 kΩ or more |
| O35-2 (DI) or A27-18 (DI) - Body ground | Always | 10 kΩ or more |
|
| ||||
| OK | |
| 11.REPLACE FUEL PUMP ECU |
Replace the fuel pump ECU (Click here).
| NEXT | |
| 12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Check the fuel pump operation.
|
| ||||
| OK | ||
| ||
| 13.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY - FUEL PUMP RELAY AND IGN FUSE) |
![]() |
Remove the circuit opening relay (C/OPN) from the engine room relay block.
Remove the fuel pump relay (F/PMP) from the engine room relay block.
Remove the IGN fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C/OPN relay (2) - IGN fuse (2) | Always | Below 1 Ω |
| C/OPN relay (5) - F/PMP relay (3) | Always | Below 1 Ω |
| C/OPN relay (2) or IGN fuse (2) - Body ground | Always | 10 kΩ or more |
| C/OPN relay (5) or F/PMP relay (3) - Body ground | Always | 10 kΩ or more |
|
| ||||
| OK | |
| 14.INSPECT FUEL PUMP RELAY (F/PMP) |
![]() |
Remove the fuel pump relay (F/PMP) from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | When no battery voltage applied to terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | When battery voltage applied to terminals 1 and 2 | Below 1 Ω |
|
| ||||
| OK | |
| 15.CHECK HARNESS AND CONNECTOR (FUEL PUMP RELAY - INTEGRATION RELAY, BATTERY AND BODY GROUND) |
![]() |
Remove the F/PMP fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F/PMP fuse | Always | Below 1 Ω |
Reinstall the F/PMP fuse.
Remove the fuel pump relay (F/PMP) from the engine room relay block.
Remove the integration relay from the engine room relay block.
Disconnect the 1B integration relay connector.
Disconnect the cable from the battery positive (+) terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F/PMP relay (1) - 1B-4 | Always | Below 1 Ω |
| F/PMP relay (5) - Positive (+) battery cable | Always | Below 1 Ω |
| F/PMP relay (2) - Body ground | Always | Below 1 Ω |
| F/PMP relay (1) or 1B-4 - Body ground | Always | 10 kΩ or higher |
| F/PMP relay (5) or Positive (+) battery cable - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||