ENGINE UNIT > INSTALLATION |
| 1. INSTALL NOISE FILTER |
RH Side:
Install the noise filter to the cylinder head cover with the bolt.
LH Side:
Install the noise filter to the cylinder head cover with the bolt.
| 2. INSTALL IGNITION COIL ASSEMBLY |
Install the 8 ignition coils with the 8 bolts.
| 3. INSTALL KNOCK SENSOR |
![]() |
Install the 4 sensors with the 4 bolts so that the sensors are angled as shown in the illustration.
Connect the 4 sensor connectors.
| 4. INSTALL NO. 11 WATER BY-PASS HOSE |
![]() |
Install the No. 11 water by-pass hose.
| 5. INSTALL ENGINE WIRE |
![]() |
Connect the 3 clamps and 4 knock sensor connectors to install the engine wire.
| 6. INSTALL NO. 1 ENGINE COVER |
![]() |
Install the No. 1 engine cover.
| 7. INSTALL NO. 2 ENGINE COVER |
![]() |
Install the No. 2 engine cover.
| 8. INSTALL SEPARATOR CASE |
![]() |
Install the separator case with the 4 bolts.
| 9. INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY |
![]() |
Install the idler pulley with the bolt.
| 10. INSTALL WATER PUMP PULLEY |
Temporarily install the pulley with the 4 bolts.
![]() |
Using SST, hold the pulley and tighten the 4 bolts.
| 11. INSTALL FRONT WATER BY-PASS JOINT |
![]() |
Install 2 new gaskets and the water by-pass joint with the 4 nuts.
Install the No. 2 water by-pass hose to the water by-pass joint.
| 12. INSTALL WATER INLET HOUSING |
![]() |
Install a new gasket to the timing chain cover.
![]() |
Install the water inlet housing with the 3 bolts.
| 13. INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY |
![]() |
Connect the hose.
Install the water by-pass pipe with the 2 bolts.
| 14. INSTALL AIR TUBE SUB-ASSEMBLY RH |
![]() |
Install the air tube with the 2 bolts.
| 15. INSTALL NO. 1 WATER BY-PASS HOSE |
![]() |
Install the water by-pass hose.
| 16. INSTALL NO. 3 ENGINE COVER |
![]() |
Install the No. 3 engine cover.
| 17. INSTALL NO. 4 ENGINE COVER |
![]() |
Install the No. 4 engine cover.
| 18. INSTALL WATER BY-PASS PIPE (w/ Oil Cooler) |
![]() |
Connect the 4 water hoses.
Install the water by-pass hose with the 2 bolts.
| 19. INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY |
![]() |
Apply adhesive to 2 or 3 threads of the oil pressure sender gauge.
![]() |
Install the oil pressure sender gauge.
![]() |
Connect the sender gauge connector.
| 20. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY LH |
Install the 2 delivery pipe spacers and 4 insulators to the cylinder head LH.
Install the delivery pipe (with injectors) to the cylinder head LH.
![]() |
Install the 2 bolts.
| *1 | Delivery Pipe |
| *2 | Injector |
| *a | CORRECT |
| *b | INCORRECT |
Connect the No. 7 wire harness connector.
| 21. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY RH |
Install the 2 delivery pipe spacers and 4 insulators to the cylinder head RH.
Install the delivery pipe (with injectors) to the cylinder head RH.
![]() |
Install the 2 bolts.
| *1 | Delivery Pipe |
| *2 | Injector |
| *a | CORRECT |
| *b | INCORRECT |
Connect the No. 6 wire harness connector.
| 22. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH |
![]() |
Install the mounting bracket with the 4 bolts.
| 23. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH |
![]() |
Install the mounting bracket with the 4 bolts.
| 24. INSTALL FRONT ENGINE MOUNTING INSULATOR RH |
![]() |
Install the mounting insulator with the nut.
| 25. INSTALL FRONT ENGINE MOUNTING INSULATOR LH |
![]() |
Install the mounting insulator with the nut.
| 26. INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY |
![]() |
Apply adhesive to 2 or 3 threads of the drain cocks.
![]() |
Install the water drain cocks.
Tighten the drain cocks up to an additional 360° so that the drain cock pipes are within the range shown in the illustration.
Install the water drain cock plugs to the water drain cocks.
| 27. INSTALL EGR COOLER ASSEMBLY |
![]() |
Install the EGR cooler with the 2 bolts.
| 28. CONNECT NO. 11 WATER BY-PASS HOSE |
![]() |
Connect the No. 11 water by-pass hose.
| 29. INSTALL NO. 8 WATER BY-PASS HOSE (w/ Oil Cooler) |
![]() |
Install the No. 8 water by-pass hose.
| 30. INSTALL NO. 8 WATER BY-PASS HOSE (w/o Oil Cooler) |
![]() |
Install the No. 8 water by-pass hose.
| 31. INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY |
![]() |
Install the No. 3 water by-pass pipe with the 2 bolts and connect the hose.
| 32. INSTALL NO. 3 AIR TUBE |
![]() |
Install the No. 3 air tube with the bolt.
![]() |
Install the wire harness clamp bracket with the bolt.
| 33. INSTALL NO. 4 AIR TUBE |
![]() |
Install the No. 4 air tube with the bolt.
![]() |
Install the wire harness clamp bracket with the bolt.
| 34. INSTALL AIR SWITCHING VALVE ASSEMBLY (for Bank 2) |
![]() |
Install a new gasket and the air switching valve with the 3 bolts.
![]() |
Install the 2 bolts.
| 35. INSTALL AIR SWITCHING VALVE ASSEMBLY (for Bank 1) |
![]() |
Install a new gasket and the air switching valve with the 3 bolts.
![]() |
Install the 2 bolts.
| 36. INSTALL NO. 2 FUEL TUBE SUB-ASSEMBLY |
![]() |
Install the No. 2 fuel tube (Click here).
| 37. INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY |
Install the No. 1 fuel pipe (Click here).
| 38. INSTALL ENGINE WIRE |
![]() |
Engine Rear Side:
Install the 4 bolts.
Connect the clamp and connector.
![]() |
Engine RH Side:
Connect the 6 clamps.
Connect the oil pressure sender gauge connector.
Connect the air switching valve connector.
Connect the noise filter connector.
Connect the fuel injector connector.
Connect the 2 VVT sensor connectors.
Connect the 4 ignition coil connectors.
Connect the 2 camshaft timing control valve connectors.
![]() |
Engine LH Side:
Connect the 8 clamps and install the engine wire with the bolt.
Connect the noise filter connector.
Connect the fuel injector connector.
Connect the engine coolant temperature sensor connector.
Connect the air switching valve connector.
Connect the crankshaft position sensor connector.
Connect the camshaft position sensor connector.
Connect the 2 VVT sensor connectors.
Connect the 4 ignition coil connectors.
Connect the 2 camshaft timing control valve connectors.