ENGINE UNIT > REMOVAL |
| 1. REMOVE ENGINE WIRE |
![]() |
Engine LH Side:
Disconnect the 2 camshaft timing control valve connectors.
Disconnect the 4 ignition coil connectors.
Disconnect the 2 VVT sensor connectors.
Disconnect the camshaft position sensor connector.
Disconnect the crankshaft position sensor connector.
Disconnect the air switching valve connector.
Disconnect the engine coolant temperature sensor connector.
Disconnect the fuel injector connector.
Disconnect the noise filter connector.
Remove the bolt and disconnect the 8 clamps.
![]() |
Engine RH Side:
Disconnect the 2 camshaft timing control valve connectors.
Disconnect the 4 ignition coil connectors.
Disconnect the 2 VVT sensor connectors.
Disconnect the fuel injector connector.
Disconnect the noise filter connector.
Disconnect the air switching valve connector.
Disconnect the oil pressure sender gauge connector.
Disconnect the 6 clamps.
![]() |
Engine Rear Side:
Disconnect the connector and clamp.
Remove the 4 bolts.
Remove the engine wire.
| 2. REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY |
![]() |
Remove the No. 1 fuel pipe (Click here).
| 3. REMOVE NO. 2 FUEL TUBE SUB-ASSEMBLY |
Remove the No. 2 fuel tube (Click here).
| 4. REMOVE AIR SWITCHING VALVE ASSEMBLY (for Bank 1) |
![]() |
Remove the 2 bolts.
![]() |
Remove the 3 bolts, air switching valve and gasket.
| 5. REMOVE AIR SWITCHING VALVE ASSEMBLY (for Bank 2) |
![]() |
Remove the 2 bolts.
![]() |
Remove the 3 bolts, air switching valve and gasket.
| 6. REMOVE NO. 4 AIR TUBE |
![]() |
Remove the bolt and wire harness clamp bracket.
![]() |
Remove the bolt and No. 4 air tube.
| 7. REMOVE NO. 3 AIR TUBE |
![]() |
Remove the bolt and wire harness clamp bracket.
![]() |
Remove the bolt and No. 3 air tube.
| 8. REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY |
![]() |
Disconnect the hose and remove the 2 bolts and No. 3 water by-pass pipe.
| 9. REMOVE NO. 8 WATER BY-PASS HOSE (w/o Oil Cooler) |
![]() |
Remove the No. 8 water by-pass hose.
| 10. REMOVE NO. 8 WATER BY-PASS HOSE (w/ Oil Cooler) |
![]() |
Remove the No. 8 water by-pass hose.
| 11. DISCONNECT NO. 11 WATER BY-PASS HOSE |
![]() |
Disconnect the No. 11 water by-pass hose.
| 12. REMOVE EGR COOLER ASSEMBLY |
![]() |
Remove the 2 bolts and EGR cooler.
| 13. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY |
![]() |
Remove the 2 water drain cock plugs from the water drain cocks.
Remove the 2 water drain cocks from the cylinder block.
| 14. REMOVE FRONT ENGINE MOUNTING INSULATOR RH |
![]() |
Remove the nut and mounting insulator.
| 15. REMOVE FRONT ENGINE MOUNTING INSULATOR LH |
![]() |
Remove the nut and mounting insulator.
| 16. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH |
![]() |
Remove the 4 bolts and mounting bracket.
| 17. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH |
![]() |
Remove the 4 bolts and mounting bracket.
| 18. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY RH |
Disconnect the No. 6 wire harness connector.
![]() |
Remove the 2 bolts and fuel delivery pipe RH.
Remove the 2 delivery pipe spacers and 4 insulators from the intake manifold.
| 19. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY LH |
Disconnect the No. 7 wire harness connector.
![]() |
Remove the 2 bolts and fuel delivery pipe LH.
Remove the 2 delivery pipe spacers and 4 insulators from the intake manifold.
| 20. REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY |
![]() |
Disconnect the sender gauge connector.
![]() |
Remove the oil pressure sender gauge.
| 21. REMOVE WATER BY-PASS PIPE (w/ Oil Cooler) |
![]() |
Remove the 2 bolts.
Disconnect the 4 water hoses and remove the water by-pass pipe.
| 22. REMOVE NO. 4 ENGINE COVER |
![]() |
Remove the No. 4 engine cover.
| 23. REMOVE NO. 3 ENGINE COVER |
![]() |
Remove the No. 3 engine cover.
| 24. REMOVE NO. 1 WATER BY-PASS HOSE |
![]() |
Remove the water by-pass hose.
| 25. REMOVE AIR TUBE SUB-ASSEMBLY RH |
![]() |
Remove the 2 bolts and air tube.
| 26. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY |
![]() |
Disconnect the hose.
Remove the 2 bolts and water by-pass pipe.
| 27. REMOVE WATER INLET HOUSING |
![]() |
Remove the 3 bolts, water inlet housing and gasket.
| 28. REMOVE FRONT WATER BY-PASS JOINT |
![]() |
Remove the No. 2 water by-pass hose from the water by-pass joint.
Remove the 4 nuts, water by-pass joint and 2 gaskets.
| 29. REMOVE WATER PUMP PULLEY |
![]() |
Using SST, hold the water pump pulley.
Remove the 4 bolts and the water pump pulley.
| 30. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY |
![]() |
Remove the bolt and idler pulley.
| 31. REMOVE FAN BRACKET SUB-ASSEMBLY |
![]() |
Remove the 5 bolts and fan bracket.
| 32. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Remove the bolt, 6 mm hexagon bolt and belt tensioner.
| 33. REMOVE SEPARATOR CASE |
![]() |
Remove the 4 bolts and separator case.
| 34. REMOVE NO. 2 ENGINE COVER |
![]() |
Remove the No. 2 engine cover.
| 35. REMOVE NO. 1 ENGINE COVER |
![]() |
Remove the No. 1 engine cover.
| 36. REMOVE ENGINE WIRE |
![]() |
Disconnect the 4 knock sensor connectors.
Disconnect the 3 clamps. Then remove the engine wire.
| 37. REMOVE NO. 11 WATER BY-PASS HOSE |
![]() |
Remove the No. 11 water by-pass hose.
| 38. REMOVE KNOCK SENSOR |
![]() |
Disconnect the 4 knock sensor connectors.
Remove the 4 bolts and 4 knock sensors.
| 39. REMOVE IGNITION COIL ASSEMBLY |
Remove the 8 bolts and 8 ignition coils.
| 40. REMOVE NOISE FILTER |
LH Side:
Remove the bolt and noise filter from the cylinder head cover.
RH Side:
Remove the bolt and noise filter from the cylinder head cover.