Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1447/47    Rear Air Mix Damper Control Servo Motor Circuit

for Preparation Click here


DESCRIPTION

The air mix rear damper servo sends pulse signals to indicate the damper position to the air conditioning amplifier. The air conditioning amplifier activates the motor (normal or reverse) based on these signals to move the rear air mix damper to the appropriate position. This adjusts the amount of air passing through the heater core after passing the evaporator and controls the temperature of the blown air.

DTC Code
DTC Detection Condition
Trouble Area
B1447/47
Rear air mix damper position does not change even if air conditioning amplifier operates rear air mix damper servo motor
  1. Air mix rear damper servo
  2. No. 2 air conditioning harness
  3. Harness or connector between No. 2 air conditioning harness and air conditioning amplifier
  4. Air conditioning amplifier

WIRING DIAGRAM


E156903E10


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (AIR MIX TARG PULSE (R))
  1. Connect the Techstream to DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Air Conditioner / Data List / Air Mix Targ Pulse (R).

  1. According to the display on the Techstream, read the Data List.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Air Mix Targ Pulse (R)
    Rear air mix servo motor target pulse /
    Min.: 0, Max.: 255
    Customized value displayed
    -

    OK:
    The display is as specified in the normal condition.


    Result 
    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to Problem Symptoms Table)
    B
    OK (When troubleshooting according to the DTC output)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
A


2.CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING HARNESS - AIR CONDITIONING AMPLIFIER)


    E127593E04
  1. Disconnect the P9 No. 2 air conditioning harness connector.

  1. Disconnect the H67 air conditioning amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    P9-2 (RBUG) - H67-21 (RBUG)
    Always
    Below 1 Ω
    P9-3 (RBUS) - H67-1 (RBUS)
    Always
    Below 1 Ω
    P9-4 (RBBU) - H67-23 (RBBU)
    Always
    Below 1 Ω
    H67-21 (RBUG) - Body ground
    Always
    10 kΩ or higher
    H67-1 (RBUS) - Body ground
    Always
    10 kΩ or higher
    H67-23 (RBBU) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the air conditioning amplifier connector.

  1. Reconnect the No. 2 air conditioning harness connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.REPLACE AIR MIX REAR DAMPER SERVO
  1. Replace the air mix rear damper servo motor (Click here).


NEXT


4.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC is not output



NG
Go to step 5
OK

END (AIR MIX REAR DAMPER SERVO IS DEFECTIVE) 

5.REPAIR OR REPLACE NO. 2 AIR CONDITIONING HARNESS
  1. Repair or replace the No. 2 air conditioning harness (Click here).


NEXT


6.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC is not output



NG
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
OK

END