Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1449/49    Rear Air Outlet Damper Control Servo Motor Circuit

for Preparation Click here


DESCRIPTION

The mode rear damper servo sends pulse signals to inform the air conditioning amplifier of the damper position. The air conditioning amplifier activates the motor (normal or reverse) based on the signals to move the rear air outlet damper to the appropriate position, which controls the air outlet modes.

HINT:
Confirm that no mechanical problem is present because this diagnostic code can be output when either a damper link or damper is mechanically locked.


DTC Code
DTC Detection Condition
Trouble Area
B1449/49
Mode rear damper position does not change even if air conditioning amplifier operates rear air outlet damper servo motor
  1. Mode rear damper servo
  2. No.2 air conditioning harness
  3. Harness or connector between No. 2 air conditioning harness and air conditioning amplifier
  4. Air conditioning amplifier

WIRING DIAGRAM


E156903E11


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (AIR OUTLET SERVO PULSE (R))
  1. Connect the Techstream to DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Air Conditioner / Data List / Air Outlet Servo Pulse (R).

  1. According to the display on the Techstream, read the Data List.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Air Outlet Servo Pulse (R)
    Rear air outlet servo motor target pulse /
    Min.: 0
    Max.: 255
    Customized value will be displayed
    -

    OK:
    The display is as specified in the normal condition.


    Result 
    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to Problem Symptoms Table)
    B
    OK (When troubleshooting according to the DTC output)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
A


2.CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING HARNESS - AIR CONDITIONING AMPLIFIER)


    E127593E04
  1. Disconnect the P9 No. 2 air conditioning harness connector.

  1. Disconnect the H67 air conditioning amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    P9-2 (RBUG) - H67-21 (RBUG)
    Always
    Below 1 Ω
    P9-3 (RBUS) - H67-1 (RBUS)
    Always
    Below 1 Ω
    P9-4 (RBBU) - H67-23 (RBBU)
    Always
    Below 1 Ω
    H67-21 (RBUG) - Body ground
    Always
    10 kΩ or higher
    H67-1 (RBUS) - Body ground
    Always
    10 kΩ or higher
    H67-23 (RBBU) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the air conditioning amplifier connector.

  1. Reconnect the No. 2 air conditioning harness connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.REPLACE MODE REAR DAMPER SERVO
  1. Replace the mode rear damper servo motor (Click here).

    HINT:
    Since the damper servo cannot be inspected while it is removed from the vehicle, replace the damper servo with a normal one.


NEXT


4.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC is not output.



NG
Go to step 5
OK

END (MODE REAR DAMPER SERVO IS DEFECTIVE) 

5.REPAIR OR REPLACE NO. 2 AIR CONDITIONING HARNESS
  1. Repair or replace No. 2 air conditioning harness (Click here).


NEXT


6.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC is not output.



NG
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
OK

END