Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch

for Preparation Click here


DESCRIPTION

If the AUTO UP/DOWN function does not operate, the cause may be one or more of the following:
  1. The ECU in the power window regulator motor determines that the power window regulator motor has not been initialized.
  2. The power window regulator switch has a malfunction.
  3. The Hall-IC in the power window regulator motor has a malfunction.
  4. The wiring between the power window regulator switch and the power window regulator motor is open or short.

WIRING DIAGRAM


B184409E06


INSPECTION PROCEDURE

1.CHECK DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    B2311 is output
    B
    B2312 is output
    C
    B2313 is output
    D
    LIN communication system DTCs are output
    E



B
GO TO DTC (B2311) (Click here)

C
GO TO DTC (B2312) (Click here)

D
GO TO DTC (B2313) (Click here)

E
GO TO LIN COMMUNICATION SYSTEM (Click here)
A


2.CHECK MANUAL UP / DOWN FUNCTION
  1. Check that the manual UP/DOWN function using the power window regulator switch can operate the front passenger side door power window (Click here).

    OK:
    Manual UP/DOWN function operates.



NG
GO TO FLOW CHART (FRONT PASSENGER SIDE POWER WINDOW MOTOR CIRCUIT) (Click here)
OK


3.READ VALUE USING TECHSTREAM (FRONT POWER WINDOW REGULATOR MOTOR RH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / P-Door Motor / Data List.

  1. According to the display on the Techstream, read the Data List.

    P-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P Door P/W Auto SW
    Front passenger side power window auto UP/DOWN switch signal / ON or OFF
    ON: Front passenger side power window auto UP/DOWN switch operated
    OFF: Front passenger side power window switch not operated
    -

OK:
The Techstream display changes when front passenger side power window switch is operated.



NG
Go to step 4
OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)  

4.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW SWITCH RH - FRONT POWER WINDOW MOTOR RH)


    B184455E12
  1. Disconnect the L2 front power window regulator switch assembly RH connector.

  1. Disconnect the L3 front power window regulator motor assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L2-8 (AUTO) - L3-4 (AUTO)
    Always
    Below 1 Ω
    L2-8 (AUTO) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the front power window regulator motor assembly RH connector.

  1. Reconnect the front power window regulator switch assembly RH connector



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH


    B184772E09
  1. Remove the L2 front power window regulator switch assembly RH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    8 (AUTO) - 1 (GND)
    AUTO UP/DOWN operation
    Below 1 Ω

  1. Reinstall the front power window regulator switch assembly RH.



NG
REPLACE FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH (Click here)
OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)