Home › Suspension › REAR SUSPENSION › REAR STABILIZER BAR

REAR STABILIZER BAR > INSTALLATION

for Preparation Click here



1. INSTALL REAR STABILIZER BUSH
  1. Install the 2 bushes to the outer side of the bush stoppers on the rear stabilizer bar.

    HINT:
    Install the bush so that the cutout faces the rear of the vehicle.



2. TEMPORARILY INSTALL REAR STABILIZER BAR
  1. Temporarily install the rear stabilizer bar with the 4 bolts.



3. TIGHTEN REAR STABILIZER BRACKET


C180768E01
  1. Install the rear stabilizer bar with the 4 bolts.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



4. TEMPORARILY INSTALL REAR STABILIZER LINK ASSEMBLY LH


C180603
  1. Temporarily install the rear stabilizer link with the 2 nuts.



5. TEMPORARILY INSTALL REAR STABILIZER LINK ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



6. INSTALL PROPELLER SHAFT ASSEMBLY (for 2WD)
(Click here)


7. INSTALL PROPELLER SHAFT ASSEMBLY (for 4WD)


    C179258E01
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Align the matchmarks on the propeller shaft flange and transfer flange.

  1. Install the propeller shaft assembly with the 8 nuts.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }



8. REMOVE TRANSFER HEAT INSULATOR (for 4WD)


    C158451
  1. Install the transfer heat insulator with the 3 bolts.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }



9. REMOVE PROPELLER SHAFT HEAT INSULATOR (for 4WD)


    C158450
  1. Install the propeller shaft heat insulator with the 2 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



10. INSTALL EXHAUST PIPE ASSEMBLY TAIL (for 3UR-FE)
  1. Connect the tailpipe to the exhaust pipe support.



    A184938E01
  1. Install a new gasket to the center exhaust pipe.

  1. Connect the tailpipe to the center exhaust pipe.

  1. Attach a new clamp to the tailpipe and center exhaust pipe. Then install the bolt to the clamp.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

    HINT:
    Install the clamp within the angle range shown in the illustration.



11. INSTALL EXHAUST PIPE ASSEMBLY TAIL (for 3UR-FBE)
  1. Connect the tailpipe to the exhaust pipe support.



    A184938E01
  1. Install a new gasket to the center exhaust pipe.

  1. Connect the tailpipe to the center exhaust pipe.

  1. Attach a new clamp to the tailpipe and center exhaust pipe. Then install the bolt to the clamp.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

    HINT:
    Install the clamp within the angle range shown in the illustration.



12. INSTALL EXHAUST PIPE ASSEMBLY TAIL (for 1UR-FE)


    A184925
  1. Connect the tailpipe to the exhaust pipe support.



    A218978E01
  1. Install a new gasket to the center exhaust pipe.

  1. Connect the tailpipe to the center exhaust pipe.

  1. Attach a new clamp to the tailpipe and center exhaust pipe. Then install the bolt to the clamp.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

    HINT:
    Install the clamp within the angle range shown in the illustration.



13. STABILIZE SUSPENSION
  1. Lower the vehicle.

  1. Press down on the vehicle several times to stabilize the suspension.



14. TIGHTEN REAR STABILIZER LINK ASSEMBLY LH
  1. Install the rear stabilizer link with the 2 nuts.

    Torque:
    98 N*m{ 999 kgf*cm , 72 ft.*lbf }



15. TIGHTEN REAR STABILIZER LINK ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.