Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1439/66    Steering Angle Sensor Initialization Incomplete

DTC    C1445/66    Vehicle Driven with Steering Angle Sensor not Initialized

for Preparation Click here


DESCRIPTION

The skid control ECU acquires the steering angle sensor zero point every time the ignition switch is turned to ON and the vehicle is driven at 40 km/h (25 mph) or more for approximately 10 seconds. The ECU also stores the previous zero point.
The steering angle sensor zero point malfunction warning will be canceled by turning the ignition switch off.

DTC Code
DTC Detection Condition
Trouble Area
C1439/66
After the steering angle sensor zero point calibration data is cleared due to, for example, fluctuations in the power source, the steering angle zero point is not obtained after 60 seconds of continuous driving
  1. Steering angle sensor
  2. Yaw rate and deceleration sensor
  3. VSC actuator (Skid control ECU)
C1445/66
Steering angle sensor zero point is not obtained when the vehicle is driven without a record of steering angle sensor zero point calibration at a speed of 36 km/h (22 mph) or more for 30 seconds or more without the brake pedal being depressed
  1. Steering angle sensor
  2. Yaw rate and deceleration sensor
  3. VSC actuator (Skid control ECU)

WIRING DIAGRAM


C193425E04


C129349E10


INSPECTION PROCEDURE

NOTICE:
  1. Before proceeding with the inspection, explain to the customer that the output DTC is related to temporary loss of the steering angle zero point calibration data, such as when the power source voltage drops when the battery is removed, and confirm whether this condition occurred.
  2. When U0073/94, U0123/62, U0124/69 and/or U0126/63 is output together with C1231/31, inspect and repair the trouble areas indicated by U0073/94, U0123/62, U0124/69 and/or U0126/63 first (Click here).
  3. When the speed sensor or the yaw rate and deceleration sensor has trouble, DTCs for the steering angle sensor may be output even when the steering angle sensor is normal. When DTCs for the speed sensor or yaw rate and deceleration sensor are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor and the yaw rate and deceleration sensor first, and then inspect and repair the steering angle sensor (Click here).
  4. When the steering angle sensor and/or yaw rate and deceleration sensor is replaced, perform zero point calibration for the applicable sensor(s) (Click here).
  5. When replacing the VSC actuator assembly, perform zero point calibration (Click here).

1.CHECK DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON again and check that no CAN communication system DTC is output.

  1. Drive the vehicle at a speed of 36 km/h (22 mph), turn the steering wheel to the right and left and check that no speed sensor or yaw rate and deceleration sensor DTCs are output (Click here).

    Result 
    Result
    Proceed to
    DTC (C1439/66 and/or C1445/66) output
    A
    DTC output (relating to CAN communication system)
    B
    DTC output (relating to speed sensor or yaw rate and deceleration sensor)
    C
    DTC not output
    D

    HINT:
    1. If there is a malfunction in the speed sensor or the yaw rate and deceleration sensor, a DTC may be output although the steering angle sensor is normal.
    2. If the speed sensor and the yaw rate and deceleration sensor DTCs are output simultaneously, repair the sensors and then inspect the steering angle sensor.
    3. If the same DTC (C1439/66 and/or C1445/66) is not output again, the DTC may have been stored due to a temporary loss of the steering angle zero point calibration data, such as when the power source voltage drops.



B
GO TO CAN COMMUNICATION SYSTEM (Click here)

C
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)

D
CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)
A


2.PERFORM STEERING ANGLE SENSOR ZERO POINT CALIBRATION
  1. Drive the vehicle straight ahead at 40 km/h (25 mph) or more for at least 10 seconds.

  1. Check that the centered position of the steering wheel is correctly set while driving straight ahead.

    HINT:
    If the front wheel alignment and steering position are adjusted as a result of an abnormal centered position of the steering wheel, acquire the yaw rate and deceleration sensor zero point again after the adjustments are completed.

    OK:
    The centered position of the steering wheel is correctly set.


NEXT


3.RECONFIRM DTC
  1. Check if the same DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B

    HINT:
    If the same DTC (C1439/66 and/or C1445/66) is not output again, the DTC may have been stored due to a temporary loss of the steering angle zero point calibration, such as when the power source voltage drops.



B
END
A


4.REPLACE STEERING ANGLE SENSOR
  1. Replace the steering angle sensor (Click here).


NEXT


5.PERFORM STEERING ANGLE SENSOR ZERO POINT CALIBRATION
  1. Drive the vehicle straight ahead at 40 km/h (25 mph) or more for at least 10 seconds.

  1. Check that the centered position of the steering wheel is correctly set while driving straight ahead.

    HINT:
    If the front wheel alignment and steering position are adjusted as a result of an abnormal centered position of the steering wheel, acquire the yaw rate and deceleration sensor zero point again after the adjustments are completed.

    OK:
    The centered position of the steering wheel is correctly set.


NEXT


6.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 35 km/h (22 mph) or more and turn the steering wheel to the right and left.

  1. Check if the same DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE VSC ACTUATOR ASSEMBLY (Click here)