Home › Engine / Hybrid System · 3UR-FBE › ENGINE CONTROL › SFI SYSTEM

DTC    P109C    Open in Fuel Pressure Switching Valve Circuit

DTC    P109D    Short in Fuel Pressure Switching Valve Circuit

for Preparation Click here


DESCRIPTION

A Flexible Fuel Vehicle (FFV) can be used with a fuel containing a high concentration of ethyl alcohol.
This FFV uses a fuel pressure switching system which changes the fuel pressure to low or high using a fuel pressure switching valve.

DTC No.
DTC Detection Condition
Trouble Area
P109C
The fuel pressure switching valve relay circuit is open or shorted to ground.
(1 trip detection logic)
  1. Fuel pressure switching valve circuit
  2. F/PMP VSV relay
  3. ECM
P109D
The fuel pressure switching valve relay circuit is shorted to the power supply.
(1 trip detection logic)
  1. Fuel pressure switching valve circuit
  2. F/PMP VSV relay
  3. ECM

MONITOR DESCRIPTION

These DTCs are stored when a malfunction is detected in the fuel pressure switching valve circuit. If the voltage of the fuel pressure switching valve circuit is different from the voltage commanded by the ECM, the ECM determines that the fuel pressure switching valve circuit is open or shorted, and stores a DTC.

CONFIRMATION DRIVING PATTERN


A198818E14

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

    HINT:
    Even if no DTCs are stored, perform the DTC clear operation to start alcohol concentration learning.

  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Wait 3 seconds or more.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  8. Read the pending DTC.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P109C or P109D.
  11. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
  12. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A196240E04


INSPECTION PROCEDURE

HINT:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.INSPECT RELAY (F/PMP VSV)
E145692E06
  1. Remove the fuel pressure control valve relay (F/PMP VSV) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When no battery voltage applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE RELAY (F/PMP VSV)
OK


2.INSPECT RELAY (POWER SOURCE VOLTAGE)
A196241E01
  1. Remove the fuel pressure control valve relay (F/PMP VSV) from the engine room relay block.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F/PMP VSV relay (2) - Body ground
    Ignition switch ON
    11 to 14 V
    F/PMP VSV relay (5) - Body ground
    Ignition switch ON
    11 to 14 V



NG
Go to step 4
OK


3.CHECK HARNESS AND CONNECTOR (F/PMP VSV RELAY - ECM)
A196242E03
  1. Remove the fuel pressure control valve relay (F/PMP VSV) from the engine room relay block.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F/PMP VSV relay (1) - D56-60 (FPCR)
    Always
    Below 1 Ω
    F/PMP VSV relay (1) or D56-60 (FPCR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

4.CHECK HARNESS AND CONNECTOR (F/PMP VSV RELAY - EFI MAIN RELAY)
A196243E01
  1. Remove the integration relay (EFI MAIN) from the engine room relay block.

  1. Remove the fuel pressure control valve relay (F/PMP VSV) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F/PMP VSV relay (2) - 1B-4
    Always
    Below 1 Ω
    F/PMP VSV relay (5) - 1B-4
    Always
    Below 1 Ω
    F/PMP VSV relay (2) or 1B-4 - Body ground
    Always
    10 kΩ or more
    F/PMP VSV relay (5) or 1B-4 - Body ground
    Always
    10 kΩ or more



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO ECM POWER SOURCE CIRCUIT (Click here)