Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > TRAC OFF Indicator Light Remains ON

for Preparation Click here


DESCRIPTION

The TRAC OFF indicator light comes on when the VSC OFF switch is operated (Click here).

WIRING DIAGRAM


C244863E01


INSPECTION PROCEDURE

NOTICE:
When replacing the VSC actuator assembly, perform zero point calibration (Click here).

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication system DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK DTC (FOR SFI SYSTEM)
  1. for 1UR-FE:
    Clear the DTC (SFI system) (Click here).
    for 3UR-FE:
    Clear the DTC (SFI system) (Click here).
    for 3UR-FBE:
    Clear the DTC (SFI system) (Click here).

  1. for 1UR-FE:
    Check the DTC (SFI system) (Click here).
    for 3UR-FE:
    Check the DTC (SFI system) (Click here).
    for 3UR-FBE:
    Check the DTC (SFI system) (Click here).
    Result 
    Result
    Proceed to
    DTC (SFI system) is not output
    A
    DTC (SFI system) is output (for 1UR-FE)
    B
    DTC (SFI system) is output (for 3UR-FE)
    C
    DTC (SFI system) is output (for 3UR-FBE)
    D



B
GO TO SFI SYSTEM (DIAGNOSTIC TROUBLE CODE CHART) (Click here)

C
GO TO SFI SYSTEM (DIAGNOSTIC TROUBLE CODE CHART) (Click here)

D
GO TO SFI SYSTEM (DIAGNOSTIC TROUBLE CODE CHART) (Click here)
A


3.PERFORM ACTIVE TEST USING TECHSTREAM (TRC(TRAC) OFF INDICATOR LIGHT)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Select the Active Test mode and operate the TRAC OFF indicator light using the Techstream.

    ABS/VSC/TRAC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    TRC(TRAC) OFF Indicator Light
    TRAC OFF indicator light
    Indicator light ON / OFF
    Observe combination meter

  1. Check that the TRAC OFF indicator light turns on and off in the combination meter when using the Techstream.

    OK:
    The TRAC OFF indicator light turns on and off in accordance with the Techstream operation.

    HINT:
    When the TRAC OFF indicator light remains illuminated, there may be an open in the wire harness of the combination meter or abnormalities in the meter circuit.



NG
GO TO METER / GAUGE SYSTEM (Click here)
OK


4.INSPECT VSC OFF SWITCH


    C179171E01
  1. Remove the VSC OFF switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 - 9
    Switch is pressed
    Below 1 Ω
    Switch is not pressed
    10 kΩ or higher



NG
REPLACE VSC OFF SWITCH (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)


    C240479E03
  1. Disconnect the A19 ECU connector.

  1. Disconnect the H29 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A19-4 (CSW) - H29-9
    Always
    Below 1 Ω
    A19-4 (CSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE VSC ACTUATOR ASSEMBLY (Click here)