VEHICLE STABILITY CONTROL SYSTEM > TEST MODE PROCEDURE |
| TEST MODE (SIGNAL CHECK) PROCEDURE (WHEN USING INTELLIGENT TESTER) |
Place the vehicle on a level surface with an inclination of less than +/-1°.
Turn the ignition switch off.
Check that the steering wheel is in the centered position.
Check that the shift lever is in P or N and apply the parking brake.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester ON.
Switch the skid control ECU to test mode using the intelligent tester.
Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check / All Signal Check or One Signal Check.
![]() |
Check that the ABS warning light and VSC OFF indicator light blink as shown in the illustration.
Start the engine.
| TEST MODE (SIGNAL CHECK) PROCEDURE (WHEN USING SST CHECK WIRE) |
Place the vehicle on a level surface with an inclination of less than +/-1°.
Turn the ignition switch off.
Check that the steering wheel is in the centered position.
Check that the shift lever is in P or N and apply the parking brake.
![]() |
Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.
Turn the ignition switch to ON.
![]() |
Check that the ABS warning light and VSC OFF indicator light blink as shown in the illustration.
Start the engine.
| MASTER CYLINDER PRESSURE SENSOR CHECK |
Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second.
Check that the skid control buzzer beeps for 3 seconds.
| YAW RATE SENSOR CHECK |
![]() |
Release the parking brake and drive the vehicle at a speed of 3 km/h (2 mph) or more, and turn the steering wheel either to the left or right 90° or more to turn the vehicle 180°.
Stop the vehicle and move the shift lever to N or P.
Check that the skid control buzzer sounds for 3 seconds.
| DECELERATION SENSOR CHECK |
Release the parking brake and drive the vehicle at a speed of 3 km/h (2 mph) or more, and turn the steering wheel either to the left or right 90° or more to turn the vehicle 180°.
Check that the skid control buzzer sounds for 3 seconds while the vehicle is turning.
| Vehicle Speed km/h (mph) | Turning Radius m (ft.) |
| 10 (6) | 7.87 (25.82) |
| 15 (9) | 17.72 (58.13) |
| 20 (12) | 31.49 (103.31) |
| 25 (16) | 49.21 (161.45) |
| SPEED SENSOR CHECK |
![]() |
Check that the ABS warning light is blinking as shown in the illustration.
Check the speed sensor signal.
Drive the vehicle straight forward at a speed of 45 km/h (28 mph) or more for several seconds.
Check that the ABS warning light goes off.

Stop the vehicle.
| END OF SENSOR CHECK |
When the sensor check is successfully completed, the ABS warning light blinks in the test mode pattern when the vehicle is stopped, and goes off when the vehicle is driven.
| READ SIGNAL CHECK FUNCTION DTCs (WHEN USING INTELLIGENT TESTER) |
Read the DTC(s) by following the instructions on the intelligent tester screen.
| READ SENSOR SIGNAL CHECK FUNCTION DTCs (WHEN USING SST CHECK WIRE) |
![]() |
Using SST, connect terminals 4 (CG), 12 (TS) and 13 (TC) of the DLC3.
Turn the ignition switch to ON.
Read the number of blinks of the ABS warning light.
![]() |
After the check, disconnect SST from terminals 4 (CG), 12 (TS) and 13 (TC) of the DLC3.
Turn the ignition switch off.
| SENSOR SIGNAL CHECK FUNCTION DTCs |
| DTC Code | Diagnosis | Trouble Area |
| C1271/71 | Low output signal of front speed sensor RH |
|
| C1272/72 | Low output signal of front speed sensor LH |
|
| C1273/73 | Low output signal of rear speed sensor RH |
|
| C1274/74 | Low output signal of rear speed sensor LH |
|
| C1275/75 | Abnormal change in output signal of front speed sensor RH |
|
| C1276/76 | Abnormal change in output signal of front speed sensor LH |
|
| C1277/77 | Abnormal change in output signal of rear speed sensor RH |
|
| C1278/78 | Abnormal change in output signal of rear speed sensor LH |
|
| C1279/79 | Deceleration sensor output voltage malfunction |
|
| C1281/81 | Master cylinder pressure sensor output malfunction |
|
| DTC Code | Diagnosis | Trouble Area |
| C0371/71 | Yaw rate sensor | Yaw rate sensor |
![]() |