DTC P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) |
DTC P0012 Camshaft Position "A" - Timing Over-Retarded (Bank 1) |
DTC P0021 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2) |
DTC P0022 Camshaft Position "A" - Timing Over-Retarded (Bank 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0011 P0021 | Intake valve timing is not adjusted in valve timing advance range (1 trip detection logic) |
|
| P0012 P0022 | Intake valve timing is not adjusted in valve timing retard range (2 trip detection logic) |
|
| Abnormal Bank | Advanced Timing Over (Valve Timing is Out of Specified Range) | Retarded Timing Over (Valve Timing is Out of Specified Range) |
| Bank 1 | P0011 | P0012 |
| Bank 2 | P0021 | P0022 |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
| P0011, P0012, P0021 or P0022 is output | A |
| P0011, P0012, P0021 or P0022 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OCV) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the intelligent tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).
Check the engine speed while operating the Oil Control Valve (OCV) using the intelligent tester.
| Tester Operation | Specified Condition |
| OCV OFF | Normal engine speed |
| OCV ON | Soon after OCV switched from OFF to ON, engine idles roughly or stalls |
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Clear DTCs (Click here).
Start the engine and warm it up.
Switch the ECM from normal mode to check mode using the intelligent tester.
Drive the vehicle for more than 10 minutes.
Read DTCs using the intelligent tester.
|
| ||||
| OK | ||
| ||
| 4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TOOTH OF TIMING CHAIN) |

Remove the cylinder head cover LH and RH.
Turn the crankshaft pulley, and align its groove with the alignment mark "0" of the timing chain cover.
Check that the alignment marks of the camshaft timing gears and camshaft timing exhaust gears are at the positions shown in the illustration.
|
| ||||
| OK | |
| 5.INSPECT CAMSHAFT OIL CONTROL VALVE ASSEMBLY (OCV) |
Inspect the camshaft oil control valve assembly .
|
| ||||
| OK | |
| 6.INSPECT OIL CONTROL VALVE FILTER |
Remove the OCV filter (Click here).
Check that the filter is not clogged.
|
| ||||
| OK | |
| 7.REPLACE CAMSHAFT TIMING GEAR |
Replace the camshaft timing gear (Click here).
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Clear DTCs (Click here).
Start the engine and warm it up.
Switch the ECM from normal mode to check mode using the intelligent tester.
Drive the vehicle for more than 10 minutes.
Read the output DTCs using the intelligent tester.
|
| ||||
| OK | ||
| ||