Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0120    Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction

DTC    P0121    Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem

DTC    P0122    Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input

DTC    P0123    Throttle / Pedal Position Sensor / Switch "A" Circuit High Input

DTC    P0220    Throttle / Pedal Position Sensor / Switch "B" Circuit

DTC    P0222    Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input

DTC    P0223    Throttle / Pedal Position Sensor / Switch "B" Circuit High Input

DTC    P2135    Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation

for Preparation Click here


DESCRIPTION

The TP sensor is mounted on the throttle body, and detects the opening angle of the throttle valve. This sensor is a non-contact type. It uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds.
The TP sensor has 2 sensor circuits, each of which transmits a signal, VTA1 and VTA2. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA terminals of the ECM.
As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air-fuel ratio correction, power increase correction and fuel-cut control.

A210489E07


DTC No.
DTC Detection Condition
Trouble Area
P0120
Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
  1. Throttle Position (TP) sensor (built into throttle body)
  2. ECM
P0121
The difference between the VTA1 and VTA2 voltages is below 0.8 V or higher than 1.6 V for 2 seconds.
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. Throttle position sensor circuit
  3. ECM
P0122
Output voltage of VTA1 0.2 V or less for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
  1. TP sensor (built into throttle body)
  2. Short in VTA1 circuit
  3. Open in VC circuit
  4. ECM
P0123
Output voltage of VTA1 4.535 V or more for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
  1. TP sensor (built into throttle body)
  2. Open in VTA1 circuit
  3. Open in E2 circuit
  4. Short between VC and VTA1 circuits
  5. ECM
P0220
Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
  1. TP sensor (built into throttle body)
  2. ECM
P0222
Output voltage of VTA2 1.75 V or less for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
  1. TP sensor (built into throttle body)
  2. Short in VTA2 circuit
  3. Open in VC circuit
  4. ECM
P0223
Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 2.02 V for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
  1. TP sensor (built into throttle body)
  2. Open in VTA2 circuit
  3. Open in E2 circuit
  4. Short between VC and VTA2 circuits
  5. ECM
P2135
Either condition (a) or (b) met (1 trip detection logic):
(a) Difference between output voltages of VTA1 and VTA2 0.02 V or less for 0.5 seconds or more
(b) Output voltage of VTA1 0.2 V or less, and VTA2 1.75 V or less, for 0.4 seconds or more
  1. Short between VTA1 and VTA2 circuits
  2. TP sensor (built into throttle body)
  3. ECM

HINT:
  1. When any of these DTCs are stored, check the throttle valve opening angle by entering the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position No. 2.
  1. Throttle Position No. 1 is the VTA1 signal, and Throttle Position No. 2 is the VTA2 signal.

    Reference (Normal Condition):

    Tester Display
    Accelerator Pedal Fully Released
    Accelerator Pedal Fully Depressed
    Throttle Position No. 1
    0.5 to 1.1 V
    3.2 to 4.8 V
    Throttle Position No. 2
    2.1 to 3.1 V
    4.6 to 5.0 V


MONITOR DESCRIPTION

P0120, P0122, P0123, P0220, P0222, P0223, P2135:
The ECM uses the Throttle Position (TP) sensor to monitor the throttle valve opening angle. There are several checks that the ECM performs to confirm the proper operation of the TP sensor.
  1. A specific voltage difference is expected between the sensor terminals, VTA1 and VTA2, for each throttle valve opening angle. If the difference between VTA1 and VTA2 is incorrect, the ECM interprets this as a malfunction in the sensor, and stores a DTC.
  1. VTA1 and VTA2 each have a specific voltage range. If VTA1 or VTA2 is outside the normal operating range, the ECM interprets this as a malfunction in the sensor, and stores a DTC.
  1. VTA1 and VTA2 should never be close to the same voltage level. If VTA1 is within 0.02 V of VTA2, the ECM determines that there is a short circuit in the sensor, and stores a DTC.
If the malfunction is not repaired successfully, a DTC is stored 10 seconds after the engine is next started.
P0121:
This sensor transmits two signals: VTA1 and VTA2. VTA1 is used to detect the throttle opening angle and VTA2 is used to detect malfunctions in VTA1. The ECM performs several checks to confirm the proper operation of the TP sensor and VTA1.
For each throttle opening angle, a specific voltage difference is expected between the outputs of VTA1 and VTA2. If the output voltage difference between the two signals deviates from the normal operating range, the ECM interprets this as a malfunction in the TP sensor. The ECM illuminates the MIL and stores the DTC.
If the malfunction is not repaired successfully, the DTC is stored 2 seconds after the engine is next started.

FAIL-SAFE

When any of these DTCs, as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM


A178644E01


INSPECTION PROCEDURE

HINT:
  1. These DTCs relate to the Throttle Position (TP) sensor.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position No. 2.

  1. Check the values displayed on the intelligent tester.

    Result 
    When Accelerator Pedal Released
    When Accelerator Pedal Depressed
    Trouble Area
    Proceed to
    Throttle Position No. 1
    Throttle Position No. 2
    Throttle Position No. 1
    Throttle Position No. 2
    0 to 0.2 V
    0 to 0.2 V
    0 to 0.2 V
    0 to 0.2 V
    VC circuit open
    A
    4.5 to 5.0 V
    4.5 to 5.0 V
    4.5 to 5.0 V
    4.5 to 5.0 V
    E2 circuit open
    0 to 0.2 V,
    or 4.5 to 5.0 V
    2.1 V to 3.1 V
    (Fail-safe)
    0 to 0.2 V,
    or 4.5 to 5.0 V
    2.1 V to 3.1 V
    (Fail-safe)
    VTA1 circuit open or ground short
    0.6 V to 1.4 V
    (Fail-safe)
    0 to 0.2 V,
    or 4.5 to 5.0 V
    0.6 V to 1.4 V
    (Fail-safe)
    0 to 0.2 V,
    or 4.5 to 5.0 V
    VTA2 circuit open or ground short
    0.5 to 1.1 V
    2.1 to 3.1 V
    3.2 to 4.8 V
    (Not fail-safe)
    4.6 to 5.0 V
    (Not fail-safe)
    TP sensor circuit normal
    B

    HINT:
    1. DTC P0121 is stored when the VTA1 and VTA2 output voltages are not consistent with the sensor characteristics. Therefore, check the freeze frame data when this DTC is stored. Use the following formula to confirm the relative differences in voltage.

      Characteristic Sensor Output:
      VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V
      VTA1: Throttle Position No. 1
      VTA2: Throttle Position No. 2

    2. If DTC P0121 is output, proceed to the "CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)".



B
Go to step 5
A


2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
A164721E05
  1. Disconnect the throttle body connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D4-5 (VC) - D56-80 (VCTA)
    Always
    Below 1 Ω
    D4-6 (VTA) - D56-78 (VTA1)
    Always
    Below 1 Ω
    D4-4 (VTA2) - D56-77 (VTA2)
    Always
    Below 1 Ω
    D4-3 (E2) - D56-79 (ETA)
    Always
    Below 1 Ω
    D4-5 (VC) or D56-80 (VCTA) - Body ground
    Always
    10 kΩ or higher
    D4-6 (VTA) or D56-78 (VTA1) - Body ground
    Always
    10 kΩ or higher
    D4-4 (VTA2) or D56-77 (VTA2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT ECM (VC VOLTAGE)
A107895E41
  1. Disconnect the throttle body connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D4-5 (VC) - D4-3 (E2)
    Ignition switch ON
    4.5 to 5.5 V



NG
REPLACE ECM (Click here)
OK


4.REPLACE THROTTLE BODY ASSEMBLY
  1. Replace the throttle body assembly (Click here).


NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    P0120, P0121, P0122, P0123, P0220, P0222, P0223 and/or P2135 are output
    A
    No DTC is output
    B



B
END
A

REPLACE ECM (Click here)