DTC P0120 Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction |
DTC P0121 Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem |
DTC P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input |
DTC P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input |
DTC P0220 Throttle / Pedal Position Sensor / Switch "B" Circuit |
DTC P0222 Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input |
DTC P0223 Throttle / Pedal Position Sensor / Switch "B" Circuit High Input |
DTC P2135 Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0120 | Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0121 | The difference between the VTA1 and VTA2 voltages is below 0.8 V or higher than 1.6 V for 2 seconds. (1 trip detection logic) |
|
| P0122 | Output voltage of VTA1 0.2 V or less for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0123 | Output voltage of VTA1 4.535 V or more for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0220 | Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0222 | Output voltage of VTA2 1.75 V or less for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0223 | Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 2.02 V for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P2135 | Either condition (a) or (b) met (1 trip detection logic): (a) Difference between output voltages of VTA1 and VTA2 0.02 V or less for 0.5 seconds or more (b) Output voltage of VTA1 0.2 V or less, and VTA2 1.75 V or less, for 0.4 seconds or more |
|
| Tester Display | Accelerator Pedal Fully Released | Accelerator Pedal Fully Depressed |
| Throttle Position No. 1 | 0.5 to 1.1 V | 3.2 to 4.8 V |
| Throttle Position No. 2 | 2.1 to 3.1 V | 4.6 to 5.0 V |

| 1.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position No. 2.
Check the values displayed on the intelligent tester.
| When Accelerator Pedal Released | When Accelerator Pedal Depressed | Trouble Area | Proceed to | ||
| Throttle Position No. 1 | Throttle Position No. 2 | Throttle Position No. 1 | Throttle Position No. 2 | ||
| 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | VC circuit open | A |
| 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V | E2 circuit open | |
| 0 to 0.2 V, or 4.5 to 5.0 V | 2.1 V to 3.1 V (Fail-safe) | 0 to 0.2 V, or 4.5 to 5.0 V | 2.1 V to 3.1 V (Fail-safe) | VTA1 circuit open or ground short | |
| 0.6 V to 1.4 V (Fail-safe) | 0 to 0.2 V, or 4.5 to 5.0 V | 0.6 V to 1.4 V (Fail-safe) | 0 to 0.2 V, or 4.5 to 5.0 V | VTA2 circuit open or ground short | |
| 0.5 to 1.1 V | 2.1 to 3.1 V | 3.2 to 4.8 V (Not fail-safe) | 4.6 to 5.0 V (Not fail-safe) | TP sensor circuit normal | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM) |
![]() |
Disconnect the throttle body connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D4-5 (VC) - D56-80 (VCTA) | Always | Below 1 Ω |
| D4-6 (VTA) - D56-78 (VTA1) | Always | Below 1 Ω |
| D4-4 (VTA2) - D56-77 (VTA2) | Always | Below 1 Ω |
| D4-3 (E2) - D56-79 (ETA) | Always | Below 1 Ω |
| D4-5 (VC) or D56-80 (VCTA) - Body ground | Always | 10 kΩ or higher |
| D4-6 (VTA) or D56-78 (VTA1) - Body ground | Always | 10 kΩ or higher |
| D4-4 (VTA2) or D56-77 (VTA2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.INSPECT ECM (VC VOLTAGE) |
![]() |
Disconnect the throttle body connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D4-5 (VC) - D4-3 (E2) | Ignition switch ON | 4.5 to 5.5 V |
|
| ||||
| OK | |
| 4.REPLACE THROTTLE BODY ASSEMBLY |
Replace the throttle body assembly (Click here).
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
| P0120, P0121, P0122, P0123, P0220, P0222, P0223 and/or P2135 are output | A |
| No DTC is output | B |
|
| ||||
| A | ||
| ||