Home › Engine / Hybrid System › 3UR-FE FUEL › FUEL INJECTOR

FUEL INJECTOR > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).



1. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the fuel pump ECU connector (Click here).

  1. Connect the cable to the negative (-) battery terminal.

  1. Start the engine. After the engine has stopped on its own, turn the ignition switch off.

    HINT:
    DTC P0171/0174 (system too lean) may be set.

  1. Crank the engine again, and then check that the engine does not start.

  1. Loosen the fuel tank cap, and then discharge the pressure in the fuel tank completely.

  1. Connect the fuel pump ECU connector (Click here).



2. REMOVE V-BANK COVER


A165576E03
  1. Raise the front of the V-bank cover to detach the 2 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.



3. REMOVE AIR CLEANER HOSE ASSEMBLY


A187008
  1. Disconnect the vacuum hose and ventilation hose.

  1. Loosen the 2 clamps.

  1. Remove the air cleaner hose.



4. DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY


    A161418
  1. Disconnect the No. 2 fuel tube from the fuel pressure regulator (for quick type) (Click here).



5. DISCONNECT FUEL TUBE SUB-ASSEMBLY


    A256329
  1. Disconnect the fuel tube from the fuel delivery pipe (for quick type) (Click here).



    A161415
  1. Disconnect the fuel tube from the No. 2 fuel delivery pipe (for quick type) (Click here).



6. DISCONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY


    A161416
  1. Disconnect the No. 1 fuel pipe from the No. 2 fuel delivery pipe (for quick type) (Click here).



7. DISCONNECT NO. 3 VENTILATION HOSE


    A161422
  1. Disconnect the No. 3 ventilation hose and No. 6 wire harness connector.



8. REMOVE NO. 3 ENGINE COVER
  1. Remove the No. 3 engine cover.



9. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY


    A256330
  1. Remove the 2 bolts and fuel delivery pipe.

    NOTICE:
    When removing the delivery pipe, hold the pipe by both ends and pull it straight upward.

  1. Remove the 2 spacers and 4 insulators from the cylinder head RH.



10. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY
  1. Remove the No. 1 engine cover.



11. REMOVE NO. 2 FUEL DELIVERY PIPE SUB-ASSEMBLY
  1. Disconnect the No. 7 wire harness connector.



    A256331
  1. Remove the 2 bolts and No. 2 fuel delivery pipe.

    NOTICE:
    When removing the delivery pipe, hold the pipe by both ends and pull it straight upward.

  1. Remove the 2 spacers and 4 insulators from the cylinder head LH.



12. REMOVE FUEL INJECTOR ASSEMBLY


    A161427
  1. Remove the fuel injector from the fuel delivery pipe, and then disconnect the injector connector.

    NOTICE:
    A149189E01
    For reinstallation, attach a tag or label to the injector shaft.



    A149190E01
  1. Remove the O-ring from the fuel injector.