Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS

WINDSHIELD GLASS > INSTALLATION

for Preparation Click here



1. CLEAN WINDSHIELD GLASS


B073128E01
  1. Using a scraper, remove the damaged stoppers, dam and adhesive from the windshield glass.

    NOTICE:
    Be careful not to damage the windshield glass.

  1. Clean the outer edge of the windshield glass with a non-residue solvent.

    NOTICE:
    1. Do not touch the windshield glass surface after cleaning it.
    2. Even if using a new windshield glass, clean the windshield glass with a non-residue solvent.



2. CLEAN VEHICLE BODY


    B073084E02
  1. Clean and shape the contact surface of the vehicle body.

    1. Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

      NOTICE:
      Do not damage the vehicle body.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

    2. Clean the contact surface of the vehicle body with a shop rag or piece of cloth saturated with cleaner.

      HINT:
      Clean the vehicle body even if all the adhesive has been removed.



3. INSTALL NO. 2 WINDSHIELD GLASS STOPPER
  1. Using a brush or sponge, coat the application area of the No. 2 stoppers with Primer G.

    NOTICE:
    1. Do not apply too much primer.
    2. Allow the primer coating to dry for 3 minutes or more.
    3. Throw away any leftover primer.

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



  1. Install 2 new No. 2 stoppers onto the windshield glass, as shown in the illustration.


    B166395E06

    HINT:
    Only 2-piece type No. 2 stoppers are supplied. Use the 2-piece type stoppers even if a 1-piece type was used.



4. INSTALL NO. 1 WINDSHIELD GLASS STOPPER


B106096E03
  1. Install 2 new No. 1 stoppers to the vehicle body, as shown in the illustration.

    HINT:
    Only 2-piece type No. 1 stoppers are supplied. Use the 2-piece type stoppers even if a 1-piece type was used.



5. INSTALL WINDOW GLASS ADHESIVE DAM
  1. Using a brush or sponge, coat the application area of adhesive dam with Primer G.

    NOTICE:
    1. Do not apply too much primer.
    2. Allow the primer coating to dry for 3 minutes or more.
    3. Throw away any leftover primer.

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



  1. Install a new adhesive dam onto the windshield glass, as shown in the illustration.


    B166396E02

    Standard:
    Area
    Specified Condition
    a
    29.2 mm (0.417 in.)

    NOTICE:
    Install the new adhesive dam along the ceramic notches.



6. INSTALL WINDSHIELD OUTSIDE UPPER MOULDING


    B166397E02
  1. Using a brush or sponge, coat the edge of the glass and the contact surface with Primer G.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.

  1. Install the windshield outside upper moulding, as shown in the illustration.

    NOTICE:
    Do not drive the vehicle for the amount of time written in the table below.

    Usage Time Frame:
    Temperature
    Usage Time Frame
    35°C (95°F)
    15 minutes
    20°C (68°F)
    1 hour 40 minutes
    5°C (41°F)
    8 hours



7. INSTALL WINDSHIELD GLASS


B194333E01
  1. Position the windshield glass.

    1. Using suction cups, place the windshield glass in the correct position.

    2. Check that the whole contact surface of the windshield glass rim is perfectly even.

    3. Align the matchmarks on the windshield glass and vehicle body.

      NOTICE:
      Check that the windshield glass stoppers are attached to the vehicle body correctly.



    B106027E04
  1. Using a brush, coat the installation surface on the vehicle body with Primer M.

    NOTICE:
    1. Do not coat the adhesive with Primer M.
    2. Do not apply too much primer.
    3. Allow the primer coating to dry for 3 minutes or more.
    4. Throw away any leftover primer.

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries



  1. Using a brush or sponge, coat the application areas that still have adhesive attached with Primer G.


    B194335E01

    NOTICE:
    1. Do not apply too much primer.
    2. Allow the primer coating to dry for 3 minutes or more.
    3. Throw away any leftover primer.

    HINT:
    1. Apply primer G onto the ceramic notches.
    2. If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



  1. Apply adhesive to the glass.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or equivalent




      B106205E01
    1. Cut off the tip of the cartridge nozzle, as shown in the illustration.

      HINT:
      After cutting off the tip, use all adhesive within the time limit described in the table below.

      Usage Time Frame:
      Temperature
      Tack-free Time
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour and 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with a cartridge.



    3. Apply adhesive to the windshield glass, as shown in the illustration.


      B194336E02

      Standard:
      Area
      Specified Condition
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)
      c
      4.0 mm (0.157 in.)



    B194333E01
  1. Install the windshield glass.

    1. Using suction cups, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.

      NOTICE:
      1. Check that the windshield glass stoppers are attached to the vehicle body correctly.
      2. Check the clearance between the vehicle body and windshield glass.

    2. Lightly press the front surface of the windshield glass to ensure a close fit.



    3. B149738E01
    4. If necessary, use a scraper to correct the level or position of adhesive that has been applied.

      HINT:
      Apply adhesive onto the windshield glass rim.

    5. Hold the windshield glass using protective tape until applied adhesive hardens.

      NOTICE:
      Do not drive the vehicle within the time limits described in the table below.

      Minimum Time:
      Temperature
      Minimum Time Prior to Driving Vehicle
      35°C (95°F)
      1 hour and 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours



8. INSTALL WINDSHIELD OUTSIDE MOULDING
  1. Using a brush or sponge, coat the application area of the moulding with Primer G.

    NOTICE:
    1. Do not apply too much primer.
    2. Allow the primer coating to dry for 3 minutes or more.
    3. Throw away any leftover primer.

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



    B194337E02
  1. Install a new moulding onto the windshield glass, as shown in the illustration.

  1. Apply Primer G to the windshield outside moulding area "a" shown in the illustration.



9. CHECK FOR LEAKAGE AND REPAIR
  1. After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.

  1. If water leaks into the cabin, allow the water to dry and add adhesive.

  1. Remove the protective tape.



10. INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)


B180555
  1. Using a T20 "TORX" socket wrench, install the inner rear view mirror with the screw.

    Torque:
    1.2 N*m{ 12 kgf*cm , 11 in.*lbf }

  1. Connect the connector.



11. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


B223747E02
  1. w/ Rear Monitor:

    1. Attach the 2 claws of the inner rear view mirror stay holder cover to the mirror, and then slide the inner rear view mirror stay holder cover in the direction indicated by the arrow in the illustration to attach the 2 claws to the roof headlining and install the inner rear view mirror stay holder cover.



    B223749
  1. w/o Rear Monitor:

    1. Attach the 6 claws.



12. INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)


B190496E01
  1. Using a T20 "TORX" socket wrench, install the inner rear view mirror with the screw.

    Torque:
    1.2 N*m{ 12 kgf*cm , 11 in.*lbf }



13. INSTALL ROOF HEADLINING ASSEMBLY

HINT:
Return the front section of the roof headlining assembly to the original position.



14. INSTALL ASSIST GRIP PLUG


B165717
  1. Install the new assist grip plug.



15. INSTALL ASSIST GRIP SUB-ASSEMBLY


B165717
  1. Install the new assist grip plug.



16. INSTALL VISOR ASSEMBLY RH (w/ Illumination)


    B191402
  1. Connect the connector.



    B190133
  1. Install the visor with the 4 screws.



17. INSTALL VISOR ASSEMBLY LH (w/ Illumination)

HINT:
Use the same procedure as for the RH side.



18. INSTALL VISOR ASSEMBLY RH (w/o Illumination)


    B190135
  1. Install the visor with the 3 screws.



19. INSTALL VISOR ASSEMBLY LH (w/o Illumination)

HINT:
Use the same procedure as for the RH side.



20. INSTALL VISOR BRACKET COVER RH


B166262
  1. Attach the 4 claws to install the visor bracket cover.



21. INSTALL VISOR BRACKET COVER LH

HINT:
Use the same procedure as for the RH side.



22. INSTALL NO. 1 ROOM LIGHT ASSEMBLY
  1. Connect the connector.

  1. Attach the 4 clips to install the No. 1 room light.



  1. Attach the 4 claws to install the lens.


    B193921



23. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (w/ Rear Seat Entertainment System)


    B191797
  1. Connect the connector.



    B193891
  1. Attach the 4 clips to install the No. 1 room light.



24. INSTALL ROOF CONSOLE BOX ASSEMBLY
  1. for Short Type:
    Install the roof console box .

  1. for Long Type:
    Install the roof console box .



25. INSTALL FRONT PILLAR GARNISH RH


    B190132E01
  1. Remove the protective cover.

  1. Attach the claw to install the front pillar garnish.

  1. Install the assist grip with the 2 bolts.

    Torque:
    9.7 N*m{ 99 kgf*cm , 86 in.*lbf }



  1. Attach the 2 claws to install the 2 assist grip plugs.


    B193062



26. INSTALL FRONT PILLAR GARNISH LH

HINT:
Use the same procedure as for the RH side.



27. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B190153E01
  1. Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.
    Paint Mark 
    Area
    Color
    RH side
    White
    LH side
    Yellow



28. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.



29. INSTALL COWL SIDE TRIM BOARD RH


    B190152
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the clip.



30. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



31. INSTALL FRONT DOOR SCUFF PLATE RH


B190151
  1. Attach the 9 claws to install the scuff plate.



32. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



33. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E161314
  1. Attach the 6 claws and 8 guides to install the cowl top ventilator louver sub-assembly.

  1. Install the 2 clips.



34. INSTALL FRONT FENDER TO COWL SIDE SEAL RH


    E161313
  1. Attach the claw and install the front fender to cowl side seal.



35. INSTALL FRONT FENDER TO COWL SIDE SEAL LH

HINT:
Use the same procedure for both sides.



36. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E146308E02
  1. Clean any metal powder off the serrated part of the wiper arm with a round wire brush or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, and then stop the wiper motor in the automatic stop position.



    E161321E01
  1. Align the blade tip with the mark on the glass, as shown in the illustration.

    HINT:
    Hold down the wiper arm hinge with your hand while tightening the nut.

  1. Tighten the nut on the front wiper arm and blade.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.



37. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E146308E02
  1. Clean any metal powder off the serrated part of the wiper arm with a round wire brush or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, and then stop the wiper motor in the automatic stop position.



    E161322E01
  1. Align the blade tip with the mark on the glass, as shown in the illustration.

    HINT:
    Hold down the wiper arm hinge with your hand while tightening the nut.

  1. Tighten the nut on the front wiper arm and blade.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.



38. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).