SFI SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the intelligent tester, use the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed | Vehicle speed/ Min.: 0 km/h, Max.: 255 km/h | Actual vehicle speed | Speed indicated on speedometer. |
| Engine Speed | Engine speed/ Min.: 0 rpm, Max.: 16383 rpm | 650 to 750 rpm: Idling | - |
| Calculate Load | Calculated load by ECM/ Min.: 0%, Max.: 100% |
| - |
| Vehicle Load | Vehicle load/ Min.: 0%, Max.: 25700% | Actual vehicle load | - |
| MAF | Air flow rate from Mass Air Flow (MAF) meter/ Min.: 0 g/sec., Max.: 655.35 g/sec. | 4.0 to 8.0 g/sec.: Idling | If the value approximately 0.0 g/sec.:
|
| Atmosphere Pressure | Atmospheric pressure/ Min.: 0 kPa, Max.: 255 kPa | Equivalent to atmospheric pressure (absolute pressure) | - |
| Coolant Temp | Engine coolant temperature: Min.: -40°C, Max.: 140°C | 80 to 100°C (176 to 212°F): After warming up | If the value -40°C (-40°F): sensor circuit open. If the value 140°C (284°F): sensor circuit shorted. |
| Intake Air | Intake air temperature/ Min.: -40°C, Max.: 140°C | Equivalent to ambient air temperature | If the value -40°C (-40°F): sensor circuit open. If the value 140°C (284°F): sensor circuit shorted. |
| Engine Run Time | Engine run time/ Min.: 0 seconds, Max.: 65535 seconds | Time after engine start | Service data |
| Initial Engine Coolant Temp | Initial engine coolant temperature/ Min.: -40°C, Max.: 140°C | Close to ambient air temperature | Service data |
| Initial Intake Air Temp | Initial intake air temperature/ Min.: -40°C, Max.: 120°C | Close to ambient air temperature | Service data |
| Battery Voltage | Battery voltage/ Min.: 0 V, Max.: 65.535 V | 11 to 14 V: Idling | - |
| Accel Sens. No.1 Volt % | Absolute Accelerator Pedal Position (APP) No. 1/ Min.: 0%, Max.: 100% | 10 to 22%: accelerator pedal is released 54 to 86%: accelerator pedal is fully depressed | - |
| Accel Sens. No.2 Volt % | Absolute APP No. 2/ Min.: 0%, Max.: 100% | 12 to 42%: accelerator pedal is released 66 to 98%: accelerator pedal is fully depressed | - |
| Accel Sensor Out No.1 | APP sensor No. 1 voltage/ Min.: 0 V, Max.: 4.98 V | - | ETCS freeze data |
| Accel Sensor Out No.2 | APP sensor No. 2 voltage/ Min.: 0 V, Max.: 4.98 V | - | ETCS freeze data |
| Accel Sensor Out No.1 | APP sensor No. 1 voltage/ Min.: 0 V, Max.: 5 V | 0.5 to 1.1 V: accelerator pedal is released 2.6 to 4.5 V: accelerator pedal is fully depressed | - |
| Accel Sensor Out No.2 | APP sensor No. 2 voltage/ Min.: 0 V, Max.: 5 V | 1.2 to 2.0 V: accelerator pedal is released 3.4 to 5.3 V: accelerator pedal is fully depressed | - |
| Accelerator Idle Position | Whether or not accelerator pedal position sensor detecting idle/ ON or OFF | ON: Idling | - |
| Accel Fully Close #1 (AD) | Accelerator fully closed value No. 1 (AD)/ Min.: 0, Max.: 4.98 V | - | ETCS service data |
| Accel Fully Close Learn #1 | Accelerator fully closed learning value No. 1/ Min.: 0, Max.: 124.512 deg | - | ETCS service data |
| Accel Fully Close Learn #2 | Accelerator fully closed learning value No. 2/ Min.: 0, Max.: 124.512 deg | - | ETCS service data |
| Throttle Sensor Volt % | Absolute throttle position sensor/ Min.: 0%, Max.: 100% |
| Value calculated based on the voltage at terminal VTA1. |
| Throttl Sensor #2 Volt % | Throttle sensor positioning #2/ Min.: 0%, Max.: 100% |
| Value calculated based on the voltage at terminal VTA2. |
| ST1 | Brake pedal signal/ ON or OFF | ON: Brake pedal depressed | - |
| System Guard | System guard/ ON or OFF | - | ETCS service data |
| Open Side Malfunction | Open side malfunction/ ON or OFF | - | ETCS service data |
| Throttle Idle Position | Whether or not throttle position sensor detecting idle/ ON or OFF |
| - |
| Throttle Require Position | Throttle requirement position/ Min.: 0 V, Max.: 5 V | 0.5 to 1.1 V: Idling | - |
| Throttle Sensor Position* | Throttle sensor positioning/ Min.: 0%, Max.: 100% |
| Recognition value for throttle opening angle on ECM. |
| Throttle Position No. 1 | Throttle position sensor No. 1 output voltage/ Min.: 0 V, Max.: 4.98 V | - | ETCS freeze data |
| Throttle Position No. 2 | Throttle position sensor No. 2 output voltage/ Min.: 0 V, Max.: 4.98 V | - | ETCS freeze data |
| Throttle Position No. 1 | Throttle position No. 1/ Min.: 0 V, Max.: 5 V |
| - |
| Throttle Position No. 2 | Throttle position No. 2/ Min.: 0 V, Max.: 5 V |
| - |
| Throttle Position Command | Throttle position command value/ Min.: 0 V, Max.: 4.98 V | 0.5 to 4.8 V | - |
| Throttle Sens Open Pos #1 | Throttle sensor opener position No. 1/ Min.: 0 V, Max.: 4.98 V | 0.6 to 1.4 V | ETCS service data |
| Throttle Sens Open Pos #2 | Throttle sensor opener position No. 2/ Min.: 0 V, Max.: 4.98 V | 1.7 to 2.5 V | ETCS service data |
| Throttle Sens Open #1(AD) | Throttle sensor opener position No. 1 (AD)/ Min.: 0 V, Max.: 4.98 V | 0.5 to 4.8 V | - |
| Throttle Motor | Whether or not throttle actuator control permitted/ ON or OFF |
| - |
| Throttle Motor Current | Throttle actuator current/ Min.: 0 A, Max.: 20 A | 0 to 3.0 A: Idling | ETCS service data |
| Throttle Motor DUTY | Throttle actuator/ Min.: 0%, Max.: 100% | 10 to 22%: Idling after engine warmed up | ETCS service data |
| Throttle Motor Current | Throttle actuator current/ Min.: 0 A, Max.: 19.92 A | 0 to 3.0 A: Idling | - |
| Throttle Motor Open Duty | Throttle actuator opening duty ratio/ Min.: 0%, Max.: 100% | 0 to 40%: During idling | When accelerator pedal depressed, duty ratio increased. |
| Throttle Motor Close Duty | Throttle actuator closed duty ratio/ Min.: 0%, Max.: 100% | 0 to 40%: During idling | When accelerator pedal released quickly, duty ratio increased. |
| Throttle Motor Duty (Open) | Throttle actuator duty ratio (open)/ Min.: 0%, Max.: 100% | 0 to 40%: Idling | ETCS service data |
| Throttle Motor Duty (Close) | Throttle actuator duty ratio (close)/ Min.: 0%, Max.: 100% | 0 to 40%: Idling | ETCS service data |
| Throttle Fully Close Learn | Throttle valve fully closed (learned value) Min.: 0, Max.: 5 V | 0.4 to 1.0 V: Accelerator pedal released | - |
| ETCS Actuator Power | Whether or not electric throttle control system power inputted/ ON or OFF |
| - |
| +BM Voltage | +BM voltage/ Min.: 0, Max.: 19.92 | 11 to 14 V: Ignition switch ON and system normal | ETCS service data |
| Actuator Power Supply | Actuator power supply/ ON or OFF | ON: Idling | ETCS service data |
| Clutch Current | Clutch current/ Min.: 0 A, Max.: 2.49 A | - | - |
| Fail Safe Drive | Whether or not fail-safe function executed/ ON or OFF |
| ETCS service data. |
| Fail Safe Drive (Main CPU) | Whether or not fail-safe function executed/ ON or OFF |
| ETCS service data. |
| Injector (Port) | Injection period of the No. 1 cylinder/ Min.: 0 ms, Max.: 32.64 ms | 2.0 to 4.0 ms: idling | - |
| Injection Volum (Cylinder 1) | Injection volume (cylinder 1)/ Min.: 0 ml, Max.: 2.048 ml | 0 to 0.5 ml | Quantity of fuel injection volume for 10 times |
| Fuel Pump/Speed Status | Fuel pump/speed status/ ON or OFF | - | Active Test support data |
| EVAP (Purge) VSV | Purge VSV control duty/ Min.: 0%, Max.: 100% | 0 to 100%: During idling | Order signal from ECM |
| Evap Purge Flow | Purge flow/ Min.: 0%, Max.: 102.4% | 0 to 100%: Idling | - |
| Purge Density Learn Value | Learning value of purge density/ Min.: -50, Max.: 350.000 | Idling: -40 to 0% | Service data |
| EVAP Purge VSV | VSV status for EVAP control/ ON or OFF | - | Active Test support data |
| Target Air-Fuel Ratio | Air fuel ratio: Min.: 0, Max.: 1.999 | 0.8 to 1.2: During idling | - |
| AF Lambda B1S1 | Short-term fuel trim associated with the Bank 1 Sensor 1/ Min.: 0, Max.: 1.999 |
| - |
| AF Lambda B2S1 | Short-term fuel trim associated with the Bank 2 Sensor 1/ Min.: 0, Max.: 1.999 |
| - |
| AFS Voltage B1S1 | Air fuel ratio sensor output voltage (for Bank 1 Sensor 1)/ Min.: 0 V, Max.: 7.999 V | 2.8 to 3.8 V: Idling | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor. |
| AFS Voltage B2S1 | Air fuel ratio sensor output voltage (for Bank 2 Sensor 1)/ Min.: 0 V, Max.: 7.999 V | 2.8 to 3.8 V: Idling | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor. |
| AFS Current B1S1 | Air fuel ratio sensor current Bank 1 Sensor 1/ Min.: -128 mA, Max.: 127.99 mA | -0.5 to 0.5 mA: Idling | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output current of sensor. |
| AFS Current B2S1 | Air fuel ratio sensor current (for Bank 2 Sensor 1)/ Min.: -128 mA, Max.: 127.99 mA | -0.5 to 0.5 mA: Idling | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output current of sensor. |
| O2S B1S2 | Heated oxygen sensor output voltage (for Bank 1 Sensor 2)/ Min.: 0 V, Max.: 1.275 V | 0.1 to 0.9 V: Driving 70 km/h (44 mph) | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor. |
| O2S B2S2 | Heated oxygen sensor output voltage (for Bank 2 Sensor 2)/ Min.: 0 V, Max.: 1.275 V | 0.1 to 0.9 V: Driving 70 km/h (44 mph) | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor. |
| O2S Impedance B1S2 | Sub heated oxygen sensor impedance (Bank 1 Sensor 2)/ Min.: 0 Ω, Max.: 21247.68 Ω | 5 to 15000 Ω | After driving approx. 10 min. in urban area |
| O2S Impedance B2S2 | Sub heated oxygen sensor impedance (Bank 2 Sensor 2)/ Min.: 0 Ω, Max.: 21247.68 Ω | 5 to 15000 Ω | After driving approx. 10 min. in urban area |
| Short FT #1 | Short-term fuel trim of Bank 1/ Min.: -100%, Max.: 99.2% | -20 to +20% | This item refers to the short-term fuel compensation used to maintain the air fuel ratio at stoichiometric air-fuel ratio. |
| Long FT #1 | Long-term fuel trim of Bank 1/ Min.: -100%, Max.: 99.2% | -20 to +20% | This item refers to the overall fuel compensation carried out in long-term to compensate a continual deviation of the short-term fuel trim from the central value. |
| Short FT #2 | Short-term fuel trim of Bank 2/ Min.: -100%, Max.: 99.2% | -20 to +20% | This item refers to the short-term fuel compensation used to maintain the air fuel ratio at stoichiometric air-fuel ratio. |
| Long FT #2 | Long-term fuel trim of Bank 2/ Min.: -100%, Max.: 99.2% | -20 to +20% | This item refers to the overall fuel compensation carried out in long-term to compensate a continual deviation of the short-term fuel trim from the central value. |
| Fuel System Status #1 | Fuel system status (Bank 1)/ OL, CL, OL Drive, OL Fault or CL Fault | CL: Idling after warming up |
|
| Fuel System Status #2 | Fuel system status (Bank 2)/ OL, CL, OL Drive, OL Fault or CL Fault | CL: Idling after warming up |
|
| Air pump pressure (absolute) | Air pump pressure (absolute)/ Min.: 0 kPa, Max.: 320 kPa | Atmospheric pressure +1 kPa or more: Air pump ON, Air switching valve open Close to atmospheric pressure: Air pump OFF, Air switching valve close | Refer to DTC P2431 (Click here) |
| Air Pump2 Pressure (Absolute) | Air pump pressure (absolute)/ Min.: 0 kPa, Max.: 320 kPa | Atmospheric pressure +1 kPa or more: Air pump ON, Air switching valve open Close to atmospheric pressure: Air pump OFF, Air switching valve close | Refer to DTC P2431 (Click here) |
| Air Pump Pulsation Pressure | Air pump pulsation pressure/ Min.: 0 kPa, Max.: 639.9 kPa | - |
|
| Air Pump2 Pulsation Pressure | Air pump pulsation pressure/ Min.: 0 kPa, Max.: 639.9 kPa | - |
|
| Secondary Air Control VSV | Secondary air injection system status ON or OFF | ON: Secondary air injection system operation | - |
| 2nd Air System Status | Secondary air system status/ ON or OFF | ON: Secondary air system operation | - |
| AI Test | AI operation prohibition/ READY or NOT RDY | READY | - |
| IGN Advance | Ignition timing advance for No. 1 cylinder/ Min.: -64 deg., Max.: 63.5 deg. | BTDC 5 to 15°: Idling | - |
| Knock Feedback Value | Feedback value of knocking/ Min.: -64° CA, Max.: 1984° CA | -22 to 0° CA: Driving, 70 km/h (44 mph) | Service data |
| Knock Correct Learn Value | Correction learning value of knocking/ Min.: -64° CA, Max.: 1984° CA | 0 to 22° CA: Driving, 70 km/h (44 mph) | Service data |
| ACIS VSV | VSV status for ACIS control/ ON or OFF | - | Active Test support data |
| VVT Control Status #1 | Variable valve timing (VVT) control status (Bank 1)/ ON or OFF | - | Active Test support data |
| VVT Control Status #2 | VVT control status (Bank 2)/ ON or OFF | - | Active Test support data |
| VVT Aim Angle #1 | VVT aim angle (Bank 1)/ Min.: 0%, Max.: 100% | 0%: Idling | VVT duty signal value during intrusive operation. |
| VVT Change Angle #1 | VVT change angle (Bank 1)/ Min.: 0° FR, Max.: 60° FR | 0 to 5° FR: Idling | Displacement angle during intrusive operation. |
| VVT OCV Duty #1 | VVT OCV operation duty (Bank 1)/ Min.: 0%, Max.: 100% | 0%: Idling | Requested duty value for intrusive operation. |
| VVT Aim Angle #2 | VVT aim angle (Bank 2)/ Min.: 0%, Max.: 100% | 0%: Idling | VVT duty signal value during intrusive operation. |
| VVT Change Angle #2 | VVT change angle (Bank 2)/ Min.: 0° FR, Max.: 60° FR | 0 to 5° FR: Idling | Displacement angle during intrusive operation. |
| VVT OCV Duty #2 | VVT OCV operation duty (Bank 2)/ Min.: 0%, Max.: 100% | 0%: Idling | Requested duty value for intrusive operation. |
| VVT Ex Hold Lrn Val #1 | VVT exhaust hold duty ratio learning value (Bank 1)/ Min.: 0%, Max.: 100% | 0 to 80%: Idling | - |
| VVT Ex Chg Angle #1 | VVT exhaust change angle (Bank 1)/ Min.: 0°FR, Max.: 60°FR | 0 to 40°FR: Idling | Displacement angle during intrusive operation. |
| VVT Ex OCV Duty #1 | VVT exhaust OCV duty (Bank 1)/ Min.: 0%, Max.: 100% | 0 to 100%: Idling | Requested duty value for intrusive operation. |
| VVT Ex Hold Lrn Val #2 | VVT exhaust hold duty ratio learning value (Bank 2)/ Min.: 0%, Max.: 100% | 0 to 80%: Idling | - |
| VVT Ex Chg Angle #2 | VVT exhaust change angle (Bank 2)/ Min.: 0°FR, Max.: 60°FR | 0 to 40°FR: Idling | Displacement angle during intrusive operation. |
| VVT Ex OCV Duty #2 | VVT exhaust OCV duty (Bank 2)/ Min.: 0%, Max.: 100% | 0 to 100%: Idling | Requested duty value for intrusive operation. |
| Catalyst Temp B1S1 | Catalyst temperature (Bank 1, Sensor 1)/ Min.: -40°C, Max.: 6513.5°C | - | - |
| Catalyst Temp B2S1 | Catalyst temperature (Bank 2, Sensor 1)/ Min.: -40°C, Max.: 6513.5°C | - | - |
| Catalyst Temp B1S2 | Catalyst temperature (Bank 1, Sensor 2)/ Min.: -40°C, Max.: 6513.5°C | - | - |
| Catalyst Temp B2S2 | Catalyst temperature (Bank 2, Sensor 2)/ Min.: -40°C, Max.: 6513.5°C | - | - |
| Starter Signal | Starter signal/ ON or OFF | ON: Cranking | - |
| Starter Control | Starter switch status/ ON or OFF | ON: Cranking | - |
| Power Steering Signal Record | Power steering switch signal/ ON or OFF | ON: Power steering operation | - |
| Starter Relay | Starter relay status/ ON or OFF | ON: Cranking | - |
| Power Steer. Sig. Record | Power steering signal (history)/ ON or OFF | ON: When steering wheel first turned after battery terminals connected | This signal status is usually ON until the cables are disconnected from the battery terminals. |
| ACC Relay | Acc relay status/ ON or OFF | ON: Cranking | - |
| Neutral Position SW Signal | PNP switch status/ ON or OFF | ON: P or N position | - |
| Stop Light Switch | Stop light switch/ ON or OFF | ON: Brake pedal is depressed | - |
| A/C Signal | A/C switch status/ ON or OFF | ON: A/C ON | - |
| Closed Throttle Position SW | Closed throttle position switch/ ON or OFF |
| - |
| Fuel Cut Condition | Fuel cut condition/ ON or OFF | ON: Fuel cut operating | - |
| Immobiliser Communication | Immobiliser communication/ ON or OFF | ON: Normal | - |
| Electrical Load Signal | Electrical load signal/ ON or OFF | ON: Headlights or defogger is turned ON | - |
| Check Mode | Check mode/ ON or OFF | ON: Check mode ON | Refer to Check Mode Procedure (Click here). |
| SPD Test Result | Check mode result for vehicle speed sensor/ Compl or Incmpl | - | - |
| AS Test Result | Check mode result for secondary air injection system/ Compl or Incmpl | - | - |
| Misfire Test Result | Check mode result for misfire monitor/ Compl or Incmpl | - | - |
| OXS1 Test Result | Check mode result for heated oxygen sensor (Bank 1)/ Compl or Incmpl | - | - |
| OXS2 Test Result | Check mode result for heated oxygen sensor (Bank 2)/ Compl or Incmpl | - | - |
| A/F Test Results #2 | Check mode result for air fuel ratio sensor (Bank 2)/ Compl or Incmpl | - | - |
| A/F Test Results #1 | Check mode result for air fuel ratio sensor (Bank 1)/ Compl or Incmpl | - | - |
| Complete Parts Monitor | Comprehensive component monitor/ Not Avl or Avail | - | - |
| Fuel System Monitor | Fuel system monitor/ Not Avl or Avail | - | - |
| Misfire Monitor | Misfire monitor/ Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT monitor/ Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT monitor/ Compl or Incmpl | - | - |
| O2S(A/FS) Heater Monitor | O2S (A/FS) heater monitor/ Not Avl or Avail | - | - |
| O2S(A/FS) Heater Monitor | O2S (A/FS) heater monitor/ Compl or Incmpl | - | - |
| O2S(A/FS) Monitor | O2S (A/FS) monitor/ Not Avl or Avail | - | - |
| O2S(A/FS) Monitor | O2S (A/FS) monitor/ Compl or Incmpl | - | - |
| A/C Monitor | A/C monitor/ Not Avl or Avail | - | - |
| A/C Monitor | A/C monitor/ Compl or Incmpl | - | - |
| 2nd Air Monitor | 2nd air monitor/ Not Avl or Avail | - | - |
| 2nd Air Monitor | 2nd air monitor/ Compl or Incmpl | - | - |
| EVAP Monitor | EVAP monitor/ Not Avl or Avail | - | - |
| EVAP Monitor | EVAP monitor/ Compl or Incmpl | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor/ Not Avl or Avail | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor/ Compl or Incmpl | - | - |
| Catalyst Monitor | Catalyst monitor/ Not Avl or Avail | - | - |
| Catalyst Monitor | Catalyst monitor/ Compl or Incmpl | - | - |
| Component Monitor ENA | Comprehensive component monitor/ Unable or Enable | - | - |
| Component Monitor CMPL | Comprehensive component monitor/ Compl or Incmpl | - | - |
| Fuel System Monitor ENA | Fuel system monitor/ Unable or Enable | - | - |
| Fuel System Monitor CMPL | Fuel system monitor/ Compl or Incmpl | - | - |
| Misfire Monitor ENA | Misfire monitor/ Unable or Enable | - | - |
| Misfire Monitor CMPL | Misfire monitor/ Compl or Incmpl | - | - |
| EGR/VVT Monitor ENA | EGR monitor/ Unable or Enable | - | - |
| EGR/VVT Monitor CMPL | EGR monitor/ Compl or Incmpl | - | - |
| Heater Monitor ENA | O2S (A/FS) heater monitor/ Unable or Enable | - | - |
| Heater Monitor CMPL | O2S (A/FS) heater monitor/ Compl or Incmpl | - | - |
| O2S(A/FS) Monitor ENA | O2S (A/FS) monitor/ Unable or Enable | - | - |
| O2S(A/FS) Monitor CMPL | O2S (A/FS) monitor/ Compl or Incmpl | - | - |
| A/C Monitor ENA | A/C monitor/ Unable or Enable | - | - |
| A/C Monitor CMPL | A/C monitor/ Compl or Incmpl | - | - |
| 2nd Air Monitor ENA | 2nd air monitor/ Unable or Enable | - | - |
| 2nd Air Monitor CMPL | 2nd air monitor/ Compl or Incmpl | - | - |
| EVAP Monitor ENA | EVAP monitor/ Unable or Enable | - | - |
| EVAP Monitor CMPL | EVAP monitor/ Compl or Incmpl | - | - |
| Heated Cat Monitor ENA | Heated catalyst monitor/ Unable or Enable | - | - |
| Heated Cat Monitor CMPL | Heated catalyst monitor/ Compl or Incmpl | - | - |
| Catalyst Monitor ENA | Catalyst monitor/ Unable or Enable | - | - |
| Catalyst Monitor CMPL | Catalyst monitor/ Compl or Incmpl | - | - |
| # Codes (Include History) | #Codes/ Min.: 0, Max.: 255 | - | Number of detected DTCs |
| MIL | MIL status/ ON or OFF | ON: MIL ON | - |
| MIL ON Run Distance | MIL ON run distance/ Min.: 0 km, Max.: 65535 km | Distance after DTC detected | - |
| Running Time from MIL ON | Running time from MIL ON/ Min.: 0 minute, Max.: 65535 minutes | Equivalent to running time after MIL was ON | - |
| Time after DTC Cleared | Time after DTC cleared/ Min.: 0 minutes, Max.: 65535 minutes | Equivalent to time after DTCs were cleared | - |
| Distance from DTC Cleared | Distance after DTC cleared/ Min.: 0 km, Max.: 65535 km | Equivalent to drive distance after DTCs were cleared | - |
| Warmup Cycle Cleared DTC | Warm-up cycle after DTC cleared/ Min.: 0, Max.: 255 | - | Number of warm-up cycles after DTC cleared |
| OBD Requirements | OBD requirement | OBD2 | - |
| Number of Emission DTC | Emission related DTCs | - | Number of emission related DTCs |
| TC and TE1 | TC and TE1 terminal of DLC3/ ON or OFF | - | - |
| Ignition Trig. Count | Ignition counter/ Min.: 0, Max.: 800 | 0 to 800 | - |
| Cylinder #1 Misfire Count to Cylinder #8 Misfire Count | Misfire ratio of the cylinder 1 to 8/ Min.: 0, Max.: 255 | 0% | - |
| All Cylinders Misfire Count | All cylinders misfire rate/ Min.: 0, Max.: 255 | 0 to 35 | - |
| Multi Cylinders Misfire Count | Multiple cylinder misfire rate/ Min.: 0 Max.: 65535 | 0 to 65535 | - |
| Misfire RPM | Engine RPM for first misfire range/ Min.: 0 rpm, Max.: 6375 rpm | 0 rpm: Misfire 0 | - |
| Misfire Load | Engine load for first misfire range/ Min.: 0 g/rev, Max.: 3.98 g/rev | 0 g/rev: Misfire 0 | - |
| Misfire Margin | Misfire monitoring/ Min.: -100%, Max.: 99.22% | -100 to 99.2% | Misfire detecting margin |
| Catalyst OT MF F/C | Catalyst over temperature misfire prevention F/C/ Not Avl or Avail | Avail: Cat OT MF F/C available Not Avl: Cat OT MF F/C not available | - |
| Cat OT MF F/C History | Catalyst over temperature misfire prevention F/C history/ ON or OFF | ON: Fuel cut operation history exists | - |
| Cat OT MF F/C Cylinder #1 | Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #2 | Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #3 | Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #4 | Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #5 | Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #6 | Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #7 | Display of fuel cut operation in No. 7 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #8 | Display of fuel cut operation in No. 8 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Power Steering Pressure | Power steering oil pressure/ Min.: -1.897 MPa, Max.: 12.799 MPa | - | - |
| ACT VSV | A/C cut status for Active Test/ ON or OFF | - | Active Test support data |
| Idle Fuel Cut | Fuel cut idle/ ON or OFF | ON: Fuel cut operation | Idle Fuel Cut = "ON" when throttle valve fully closed and engine speed over 2800 rpm. |
| FC TAU | Fuel cut TAU: Fuel cut during very light load/ ON or OFF | ON: Fuel cut operation | The fuel cut being performed under very light load to prevent the engine combustion from becoming incomplete. |
| Model Code | Model code | - | Identifying the model code: USK6## |
| Engine Type | Engine type | - | Identifying the engine type: 3URFE |
| Cylinder Number | Number of cylinders/ Min.: 0, Max.: 255 | - | Identifying number of cylinders: 8 |
| Transmission Type | Transmission type | - | Identifying the transmission type: ECT 6th |
| Destination | Destination | - | Identifying the destination: A (America) |
| Model Year | Model year/ Min.: 1900, Max.: 2155 | - | Identifying the model year: 200# |
| System Identification | System identification | - | Identifying the engine system: Gasoline (gasoline engine) |
| Engine Speed of Cyl #1 | Engine RPM for cylinder 1/ Min.: 0 rpm, Max.: 25600 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #2 | Engine RPM for cylinder 2/ Min.: 0 rpm, Max.: 25600 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #3 | Engine RPM for cylinder 3/ Min.: 0 rpm, Max.: 25600 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #4 | Engine RPM for cylinder 4/ Min.: 0 rpm, Max.: 25600 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #5 | Engine RPM for cylinder 5/ Min.: 0 rpm, Max.: 25600 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #6 | Engine RPM for cylinder 6/ Min.: 0 rpm, Max.: 25600 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #7 | Engine RPM for cylinder 7/ Min.: 0 rpm, Max.: 25600 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #8 | Engine RPM for cylinder 8/ Min.: 0 rpm, Max.: 25600 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Av Engine Speed of All Cyl | Engine RPM for all cylinders/ Min.: 0 rpm, Max.: 25600 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| SPD (NT) | Input shaft speed/ Min.: 0 rpm, Max.: 12750 rpm | Lock-up is
| Data is displayed in increments of 50 rpm |
| SPD (SP2) | Output shaft speed/ Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed) | - |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Injection Volume | Change injection volume | Between -12% and 25% |
|
| Control the Injection Volume for A/F Sensor | Change injection volume | Lower by 12.5% or increase 25% |
|
| Activate the VSV for Secondary Air Control | Activate the Secondary Air System | ON/OFF |
|
| Activate the VSV for Intake Control | Activate VSV for intake control | ON/OFF | - |
| Activate the VSV for Evap Control | Activate purge VSV control | ON/OFF | - |
| Control the A/C Cut Signal | Control A/C cut signal | ON/OFF | - |
| Control the Fuel Pump / Speed | Activate fuel pump | ON/OFF | Engine is stopped. |
| Connect the TC and TE1 | Turn on and off TC and TE1 connection | ON/OFF |
|
| Control the Idle Fuel Cut Prohibit | Prohibit idling fuel cut control | ON/OFF | - |
| Prohibit the Catalyst OT Misfire prevent F/C | Prohibit catalyst overheat malfunction prevention fuel cut operation during misfire | ON: Fuel cut is prohibited | Confirm that the Vehicle is Stopped and Engine Speed is 3000 rpm or less. |
| Activate the Starter Relay | Activate the starter relay | ON/OFF | Engine is stopped. |
| Activate the ACC Cut Relay | Activate the ACC CUT relay | ON/OFF | Engine is stopped. |
| Control the ETCS Open/Close Slow Speed | Throttle actuator | Close/Open Open: throttle valve opens slowly | This test is possible when the following conditions are met:
|
| Control the ETCS Open/Close Fast Speed | Throttle actuator | Close/Open Open: throttle valve opens fast | Same as above. |
| Control the VVT Linear (Bank 1) | Control Variable Valve Timing (VVT) [Bank 1] | -128 to 127% This valve added to present OCV control duty 100%: Maximum advance -100%: Maximum retard |
|
| Control the VVT System (Bank 1) | Turn on and off Oil Control Valve (OCV) | ON/OFF |
|
| Control the VVT Linear (Bank 2) | Control Variable Valve Timing (VVT) [Bank 2] | -128 to 127% This valve added to present OCV control duty 100%: Maximum advance -100%: Maximum retard |
|
| Control the VVT System (Bank 2) | Turn on and off Oil Control Valve (OCV) | ON/OFF |
|
| Control the VVT Exhaust Linear (Bank 1) | Control VVT (Bank 1) | 128 to 127% This valve added to present OCV control duty 100%: Maximum advance -100%: Maximum retard |
|
| Control the VVT Exhaust Linear (Bank 2) | Control VVT (Bank 2) | 128 to 127% This valve added to present OCV control duty 100%: Maximum advance -100%: Maximum retard |
|
| Control the Cylinder #1 Fuel Cut | Cylinder #1 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the Cylinder #2 Fuel Cut | Cylinder #2 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the Cylinder #3 Fuel Cut | Cylinder #3 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the Cylinder #4 Fuel Cut | Cylinder #4 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the Cylinder #5 Fuel Cut | Cylinder #5 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the Cylinder #6 Fuel Cut | Cylinder #6 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the Cylinder #7 Fuel Cut | Cylinder #7 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the Cylinder #8 Fuel Cut | Cylinder #8 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the All Cylinders Fuel Cut | All cylinder fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Check the Cylinder Compression*2 | Check the cylinder compression pressure | ON/OFF | Fuel injection and ignition stop in all cylinders. |
| SYSTEM CHECK |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility.
Perform the System Check by referring to the table below.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Air Injection Check (Automatic Mode) | Perform secondary air injection system operation automatically | With warm engine, ignition switch turned off once |
|
| Air Injection Check (Manual Mode) | Perform 7 operations in order to operate air injection system monitor manually | With warm engine, ignition switch turned off once |
|