Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P2431    Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank1

DTC    P2432    Secondary Air Injection System Air Flow / Pressure Sensor Circuit Low Bank1

DTC    P2433    Secondary Air Injection System Air Flow / Pressure Sensor Circuit High Bank1

DTC    P2436    Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank 2

DTC    P2437    Secondary Air Injection System Air Flow / Pressure Sensor Circuit Low Bank 2

DTC    P2438    Secondary Air Injection System Air Flow / Pressure Sensor Circuit High Bank 2

for Preparation Click here


DESCRIPTION

The Secondary Air injection (AIR) system consists of an air pump, the Air Switching Valve (ASV), a pressure sensor, the Air Injection Control Driver (AID) and the ECM. For a short time after cold engine starts, the AIR system pumps secondary air to the exhaust port of the cylinder head to purify the exhaust emissions. The secondary air is supplied by the air pump and is pumped to the exhaust port through the ASV.
The AID drives the ASV and the air pump according to command signals transmitted by the ECM. The pressure sensor detects the pressure in the secondary air passage when the AIR system is ON and OFF, and transmits a pressure signal to the ECM.
The AID is not only equipped to drive the pump and valve, but also with a diagnosis function to detect malfunctions in the AIR system circuit.

HINT:
As a large current is required to drive the air pump and ASV, an AID is installed to this system.


A162565E01


DTC No.
DTC Detection Condition
Trouble Area
P2431
P2436
Pressure sensor indicates less than 45.6 kPa (342 mmHg), or more than 135 kPa (1013 mmHg) (2 trip detection logic)
  1. Pressure sensor
  2. Open or short in pressure sensor circuit
  3. ECM
P2432
P2437
While engine running, voltage output of pressure sensor remains below 0.5 V (1 trip detection logic)
  1. Pressure sensor
  2. Open or short in pressure sensor circuit
  3. ECM
P2433
P2438
While engine running, voltage output of pressure sensor remains above 4.5 V (1 trip detection logic)
  1. Pressure sensor
  2. Open or short in pressure sensor circuit
  3. ECM

MONITOR DESCRIPTION

A085160E13
The ECM monitors the pressure in the secondary air passage using the pressure sensor located on the air switching valve in the secondary air injection system.
If there is a defect in the sensor or the sensor circuit, the voltage level deviates from the normal operating range, the ECM interprets this deviation as a malfunction in the pressure sensor or circuit and stores a DTC.

WIRING DIAGRAM

Refer to DTC P0412 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR - ECM)
A161478E11
  1. Disconnect the pressure sensor connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D37-3 (AIP) - A27-54 (AIP)
    Always
    Below 1 Ω
    D37-2 (VC) - D56-67 (VCV1)
    Always
    Below 1 Ω
    D37-4 (E2) - D56-98 (ETHA)
    Always
    Below 1 Ω
    D38-3 (AIP2) - A27-53 (AIP2)
    Always
    Below 1 Ω
    D38-2 (VC2) - D56-67 (VCV1)
    Always
    Below 1 Ω
    D38-4 (E22) - D56-97 (ETHW)
    Always
    Below 1 Ω
    D37-3 (AIP) or A27-54 (AIP) - Body ground
    Always
    10 kΩ or higher
    D37-2 (VC) or D56-67 (VCV1) - Body ground
    Always
    10 kΩ or higher
    D38-3 (AIP2) or A27-53 (AIP2) - Body ground
    Always
    10 kΩ or higher
    D38-2 (VC2) or D56-67 (VCV1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT AIR SWITCHING VALVE (PRESSURE SENSOR)
A165753E02
  1. Connect a pressure gauge to the air pressure sensor as shown in the illustration.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Air pump pressure (absolute) and Air Pump2 Pressure (Absolute).

  1. Check that the pressure displayed on the intelligent tester fluctuates when applying the pressure to the pressure sensor with the pressure gauge.

    OK:
    Pressure fluctuates in response to pressure applied with pressure gauge.

    HINT:
    The intelligent tester displays the air pump pressure as absolute pressure.



NG
REPLACE AIR SWITCHING VALVE (Click here)
OK

REPLACE ECM (Click here)