Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0137    Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)

DTC    P0157    Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2)

for Preparation Click here


DESCRIPTION

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric air-fuel level. For the purpose of helping the ECM to deliver accurate air-fuel ratio control, a Heated Oxygen (HO2) sensor is used.
The HO2 sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).
When the air-fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The HO2 sensor informs the ECM that the post-TWC air-fuel ratio is lean (low voltage, i.e. less than 0.45 V).
Conversely, when the air-fuel ratio is richer than the stoichiometric air-fuel level, the oxygen concentration in the exhaust gas becomes lean. The HO2 sensor informs the ECM that the post-TWC air-fuel ratio is rich (high voltage, i.e. more than 0.45 V). The HO2 sensor has the property of changing its output voltage drastically when the air-fuel ratio is close to the stoichiometric level.
The ECM uses the supplementary information from the HO2 sensor to determine whether the air-fuel ratio after the TWC is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the HO2 sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air-fuel ratio control.

A115539E07


DTC No.
DTC Detection Condition
Trouble Area
P0137
P0157
  1. Low voltage (open):
    During active air-fuel ratio control, following conditions (a) and (b) met for certain period of time (2 trip detection logic)
    1. (a) HO2 sensor voltage output less than 0.21 V
    1. (b) Target air-fuel ratio rich
  1. Open in HO2 sensor (for Bank 1, 2) circuit
  2. HO2 sensor (bank 1, 2 sensor 2)
  3. HO2 sensor heater (bank 1, 2 sensor 2)
  4. Air-fuel Ratio (A/F) sensor (bank 1, 2 sensor 1)
  5. Integration relay
  6. Gas leak from exhaust system

MONITOR DESCRIPTION

  1. Active Air-Fuel Ratio Control
    The ECM usually performs air-fuel ratio feedback control so that the Air-Fuel Ratio (A/F) sensor output indicates a near stoichiometric air-fuel level. This vehicle includes active air-fuel ratio control in addition to regular air-fuel ratio control. The ECM performs active air-fuel ratio control to detect any deterioration in the Three-Way Catalytic Converter (TWC) and Heated Oxygen (HO2) sensor malfunctions (refer to the diagram below).
    Active air-fuel ratio control is performed for approximately 15 to 20 seconds while driving with a warm engine. During active air-fuel ratio control, the air-fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.
  1. Open in Heated Oxygen (HO2) Sensor Circuit (DTC P0137 and P0157)
    During active air-fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the Three-Way Catalytic Converter (TWC) by forcibly regulating the air-fuel ratio to become rich or lean. If the HO2 sensor has an open, or the voltage output of the sensor decreases significantly, the OSC indicates an extraordinarily high value. Even if the ECM attempts to continue regulating the air-fuel ratio to become rich or lean, the HO2 sensor output does not change.
    While performing active air-fuel ratio control, when the target air-fuel ratio is rich and the HO2 sensor voltage output is less than 0.21 V (lean), the ECM interprets this as an abnormally low sensor output voltage and stores DTC P0137 or P0157.
    *: The TWC has the capability to store oxygen. The OSC and the emission purification capacity of the TWC are mutually related. The ECM determines whether the catalyst has deteriorated based on the calculated OSC value.

    A234468E24


WIRING DIAGRAM


A167571E04


CONFIRMATION DRIVING PATTERN

HINT:
  1. This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.
  2. Performing this confirmation pattern will activate the heated oxygen sensor monitor. (The catalyst monitor is performed simultaneously.) This is very useful for verifying the completion of the repair.

NOTICE:
This test will not be completed if the vehicle is driven under absolutely constant speed conditions such as with cruise control activated.


A115372E98

  1. Connect an intelligent tester to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the intelligent tester on.
  4. Enter the following menus: Powertrain / Engine and ECT / DTC / Clear.
  5. Clear DTCs.
  6. Start the engine and warm it up (Proceed to "A").
  7. Drive the vehicle at between 90 km/h and 110 km/h (56 mph and 68 mph) for at least 10 minutes (Proceed to "B").
  8. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  9. Input DTCs: P0137 and P0157.
  10. Check that DTC MONITOR is NORMAL. If DTC MONITOR is INCOMPLETE, perform the drive pattern adding the vehicle speed.

INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the intelligent tester.
  1. Connect the intelligent tester to the DLC3.
  2. Start the engine and turn the intelligent tester on.
  3. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
  5. Perform the Active Test operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
  6. Monitor the output voltages of the A/F and HO2 sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the intelligent tester.

HINT:
  1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


Tester Display (Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
+12.5%
Rich
Less than 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
-12.5%
Lean
More than 3.4 V
O2S B1S2 or O2S B2S2
(HO2)
+12.5%
Rich
More than 0.55 V
O2S B1S2 or O2S B2S2
(HO2)
-12.5%
Lean
Less than 0.4 V

NOTICE:
The Air-Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.


Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E08
A151324E08
A150787E08
A150788E06
-
2
A150787E08
A150790E01
A150787E08
A150788E06
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150787E08
A151324E08
A150787E08
A150790E01
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150787E08
A150790E01
A150787E08
A150790E01
  1. Injector
  2. Fuel pressure
  3. Gas leak from exhaust system (Air-fuel ratio extremely rich or lean)
  1. Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.

HINT:
  1. If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leak.

    OK:
    No gas leak.



NG
REPAIR OR REPLACE EXHAUST GAS LEAK POINT
OK


2.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
A117841E28
  1. Disconnect the HO2 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (HT1B) - 2 (+B)
    20°C (68°F)
    11 to 16 Ω
    1 (HT1B) - 4 (E1)
    Always
    10 kΩ or higher
    1 (HT2B) - 2 (+B)
    20°C (68°F)
    11 to 16 Ω
    1 (HT2B) - 4 (E1)
    Always
    10 kΩ or higher



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


3.INSPECT INTEGRATION RELAY (EFI MAIN RELAY)
A148742E04
  1. Remove the integration relay from the engine room relay block.

  1. Inspect the EFI NO. 1 fuse.

    1. Remove the EFI NO. 1 fuse from the integration relay.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Tester Connection
      Condition
      Specified Condition
      EFI NO. 1 fuse
      Always
      Below 1 Ω

    3. Reinstall the EFI NO. 1 fuse.

  1. Inspect the EFI MAIN relay.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1B-4
      When no battery voltage applied to terminals 1B-2 and 1B-3
      10 kΩ or higher
      When battery voltage applied to terminals 1B-2 and 1B-3
      Below 1 Ω



NG
REPLACE INTEGRATION RELAY
OK


4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
A164723E03

A164717E06

  1. Disconnect the HO2 sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D17-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    D18-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Turn the ignition switch off.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D17-1 (HT1B) - D56-45 (HT1B)
    Always
    Below 1 Ω
    D17-3 (OX1B) - D56-114 (OX1B)
    Always
    Below 1 Ω
    D17-4 (E1) - D56-115 (EX1B)
    Always
    Below 1 Ω
    D18-1 (HT2B) - D56-44 (HT2B)
    Always
    Below 1 Ω
    D18-3 (OX2B) - D56-112 (OX2B)
    Always
    Below 1 Ω
    D18-4 (E1) - D56-113 (EX2B)
    Always
    Below 1 Ω
    D17-1 (HT1B) or D56-45 (HT1B) - Body ground
    Always
    10 kΩ or higher
    D17-3 (OX1B) or D56-114 (OX1B) - Body ground
    Always
    10 kΩ or higher
    D18-1 (HT2B) or D56-44 (HT2B) - Body ground
    Always
    10 kΩ or higher
    D18-3 (OX2B) or D56-112 (OX2B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE HEATED OXYGEN SENSOR
  1. Replace the heated oxygen sensor (Click here).


NEXT


6.PERFORM CONFIRMATION DRIVING PATTERN (DTC P0137 OR P0157)

HINT:
Refer to the Confirmation Driving Pattern.


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input DTCs: P0137 or P0157.

  1. Check that DTC MONITOR is NORMAL. If DTC MONITOR is INCOMPLETE, perform the drive pattern adding the vehicle speed.

    Result 
    Display (DTC Output)
    Proceed to
    NORMAL
    (No DTC output)
    A
    ABNORMAL
    (P0137 or P0157 detected)
    B



B
REPLACE AIR FUEL RATIO SENSOR (Click here)
A

END