DTC P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) |
DTC P0157 Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0137 P0157 |
|
|



| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 or AFS Voltage B2S1 (A/F) | +12.5% | Rich | Less than 3.1 V |
| AFS Voltage B1S1 or AFS Voltage B2S1 (A/F) | -12.5% | Lean | More than 3.4 V |
| O2S B1S2 or O2S B2S2 (HO2) | +12.5% | Rich | More than 0.55 V |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5% | Lean | Less than 0.4 V |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() ![]() | ![]() ![]() | - |
| 2 | ![]() ![]() | ![]() ![]() |
|
| 3 | ![]() ![]() | ![]() ![]() |
|
| 4 | ![]() ![]() | ![]() ![]() |
|
| 1.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leak.
|
| ||||
| OK | |
| 2.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
Inspect the heated oxygen sensor (Click here).
|
| ||||
| OK | |
| 3.INSPECT INTEGRATION RELAY (EFI MAIN RELAY) |
![]() |
Remove the integration relay from the engine room relay block.
Inspect the EFI NO. 1 fuse.
Remove the EFI NO. 1 fuse from the integration relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| EFI NO. 1 fuse | Always | Below 1 Ω |
Reinstall the EFI NO. 1 fuse.
Inspect the EFI MAIN relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1C-1 - 1B-4 | When no battery voltage applied to terminals 1B-2 and 1B-3 | 10 kΩ or higher |
| When battery voltage applied to terminals 1B-2 and 1B-3 | Below 1 Ω |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
Disconnect the HO2 sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D17-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| D18-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
Turn the ignition switch off.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D17-1 (HT1B) - D56-45 (HT1B) | Always | Below 1 Ω |
| D17-3 (OX1B) - D56-114 (OX1B) | Always | Below 1 Ω |
| D17-4 (E1) - D56-115 (EX1B) | Always | Below 1 Ω |
| D18-1 (HT2B) - D56-44 (HT2B) | Always | Below 1 Ω |
| D18-3 (OX2B) - D56-112 (OX2B) | Always | Below 1 Ω |
| D18-4 (E1) - D56-113 (EX2B) | Always | Below 1 Ω |
| D17-1 (HT1B) or D56-45 (HT1B) - Body ground | Always | 10 kΩ or higher |
| D17-3 (OX1B) or D56-114 (OX1B) - Body ground | Always | 10 kΩ or higher |
| D18-1 (HT2B) or D56-44 (HT2B) - Body ground | Always | 10 kΩ or higher |
| D18-3 (OX2B) or D56-112 (OX2B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.REPLACE HEATED OXYGEN SENSOR |
Replace the heated oxygen sensor (Click here).
| NEXT | |
| 6.PERFORM CONFIRMATION DRIVING PATTERN (DTC P0137 OR P0157) |
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTCs: P0137 or P0157.
Check that DTC MONITOR is NORMAL. If DTC MONITOR is INCOMPLETE, perform the drive pattern adding the vehicle speed.
| Display (DTC Output) | Proceed to |
| NORMAL (No DTC output) | A |
| ABNORMAL (P0137 or P0157 detected) | B |
|
| ||||
| A | ||
| ||