AUTOMATIC TRANSMISSION SYSTEM > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| N Range Status | Shift lever N status/ ON or OFF |
| - |
| Neutral Position SW Signal | PNP switch status/ ON or OFF |
| When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Stop Light Switch | Stop light switch status/ ON or OFF | Brake pedal is:
| - |
| SPD (NT) | Input shaft speed/ Min.: 0 rpm Max.: 12750 rpm | Lock-up is:
| Data is displayed in increments of 50 rpm |
| SPD (SP2) | Output shaft speed/ Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph) | Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed) | - |
| Shift SW Status (P Range) | PNP switch status/ ON or OFF |
| When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW Status (R Range) | PNP switch status/ ON or OFF |
| When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW Status (N Range) | PNP switch status/ ON or OFF |
| When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW Status (N, P Range) Supported | Status of PNP switch (N or P) supported/ Supp or Unsupp | - | - |
| Shift SW Status (N, P Range) | PNP switch status/ ON or OFF |
| - |
| Sports Shift Up SW | Sport shift up switch status/ ON or OFF |
| - |
| Sports Shift Down SW | Sport shift down switch status/ ON or OFF |
| - |
| Sports Mode Selection SW | Sport mode select switch status/ ON or OFF |
| - |
| Shift SW Status (D Range) | PNP switch status/ ON or OFF |
| When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| A/T Oil Temperature 1 | No. 1 ATF temperature sensor value/ Min.: -40°C (-40°F) Max.: 215°C (419°F) |
| If value is -40°C (-40°F) or 215°C (419°F), No. 1 ATF temperature sensor circuit is open or shorted |
| A/T Oil Temperature 2 | No. 2 ATF temperature sensor value/ Min.: -40°C (-40°F) Max.: 215°C (419°F) |
| If value is -40°C (-40°F) or 215°C (419°F), No. 2 ATF temperature sensor circuit is open or shorted |
| Lock Up | Lock-up/ ON or OFF | Lock-up is:
| - |
| Shift Status | ECM gear shift command/ 1st, 2nd, 3rd, 4th, 5th or 6th |
| - |
| SLT Solenoid Status | Shift solenoid SLT status/ ON or OFF |
| - |
| SLU Solenoid Status | Shift solenoid SLU status/ ON or OFF | Shift solenoid SLU is:
| - |
| AT Fluid | Flex lock-up judder judgment/ ON or OFF |
| - |
| PERFORM ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Solenoid (SLU) | Operate the shift solenoid SLU | ON or OFF | [Vehicle Condition]
|
| Activate the Solenoid (SLT)* | Operate the shift solenoid SLT and raise line pressure | ON or OFF
| [Vehicle Condition]
|
| Activate the Solenoid (S1) | Operate the shift solenoid S1 | ON or OFF | [Vehicle Condition]
|
| Activate the Solenoid (S2) | Operate the shift solenoid S2 | ON or OFF | [Vehicle Condition]
|
| Activate the Solenoid (S3) | Operate the shift solenoid S3 | ON or OFF | [Vehicle Condition]
|
| Activate the Solenoid (S4) | Operate the shift solenoid S4 | ON or OFF | [Vehicle Condition]
|
| Activate the Lock Up | Control shift solenoid SLU to set automatic transmission to lock-up condition | ON or OFF | Possible to check shift solenoid valve SLU operation [Vehicle Condition]
|
| Control the Shift Position | Operate shift solenoid valve and set each shift position by yourself |
| Possible to check operation of shift solenoid valves [Vehicle Condition] 50 km/h (30 mph) or less |
| Activate the Solenoid (SR) | Operate the shift solenoid SR | ON or OFF | [Vehicle Condition]
|
| Activate the Solenoid (SL1) | Operate the shift solenoid SL1 | ON or OFF | [Vehicle Condition]
|
| Activate the Solenoid (SL2) | Operate the shift solenoid SL2 | ON or OFF | [Vehicle Condition]
|