Home › Drivetrain · AB60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

DTC    P2714    Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)

for Preparation Click here


DESCRIPTION


C161167E02

Shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and the vehicle speed sensor. The ECM adjusts the duty ratio* of the shift solenoid valve SLT to control the hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.

HINT:
*: The duty ratio is the ratio of the current ON time (A) to the total of the current ON and OFF time (A + B).
Duty Ratio (%) = A / (A + B) x 100


DTC Code
DTC Detection Condition
Trouble Area
P2714
The ECM detects a malfunction in shift solenoid valve SLT (ON side) according to the difference in speed of the turbine and output shaft, and also by the oil pressure (1 trip detection logic).
  1. Shift solenoid valve SLT remains open or closed
  2. Shift solenoid valve S1, S2, S3, S4 or SL2 remains open or closed
  3. Gear 6 incorrect ratio (sequence valve) or 1-2 shift valve is stuck
  4. Valve body is blocked
  5. Automatic transmission (clutch, brake, gear, etc.)

MONITOR DESCRIPTION

The ECM calculates the amount of heat absorbed by the friction material based on the difference in speed (clutch slippage) between the turbine and output shaft. The ECM illuminates the MIL and stores this DTC when the amount of heat absorption exceeds the specified value.
There are two reasons that the speed may be different.
  1. When shift solenoid valve SLT remains ON, oil pressure decreases, which causes the clutch engagement force to decrease.
  2. When the shift solenoid valve remains ON or OFF, the gear position commanded by the ECM and the actual gear position are not the same.

NOTICE:
If the vehicle continues to be driven under these conditions, the clutch will burn out and the vehicle will no longer be drivable.


INSPECTION PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P2714)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using the intelligent tester.
    Result 
    Result
    Proceed to
    Only P2714 is output
    A
    P2714 and other DTCs are output
    B

    HINT:
    If any other codes besides P2714 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT)

NOTICE:
  1. Perform the test while the ATF temperature is between 50 and 80°C (122 and 176°F).
  2. Be careful to prevent the hose of SST from interfering with the exhaust pipe.
  3. Perform the test with the A/C off.

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.



    C219461E01
  1. Remove the test plug on the transmission case and connect SST.

SST
09992-00095   (09992-00231, 09992-00271)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and warm it up.

  1. Measure the line pressure with SST.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  1. According to the display on the intelligent tester, perform the Active Test.

  1. Measure the line pressure.

    Engine and ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Solenoid (SLT)*
    Operate the shift solenoid SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling

    HINT:
    *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Please note that the pressure values in the Active Test and Hydraulic Test are different.

    OK:
    The line pressure changes as specified when performing the Active Test.



NG
Go to step 7
OK


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (RUNNING TEST)

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTC (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  1. According to the display on the intelligent tester, perform the Active Test.

    HINT:
    While driving, the shift position can be forcibly changed with the intelligent tester.


    Engine and ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Shift Position
    Operate shift solenoid valves and set each shift position by yourself
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check operation of the shift solenoid valves.
    [Vehicle Condition]
    50 km/h (30 mph) or less

    HINT:
    1. This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.
    2. The 4th to 5th and 5th to 6th up-shift must be performed with the accelerator pedal released.
    3. The 6th to 5th and 5th to 4th down-shift must be performed with the accelerator pedal released.
    4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
    5. The shift position commanded by the ECM is shown in the Data List display on the intelligent tester.

  1. Compare the ECM gear shift command and actual gear position.

    Result 
    ECM gear shift command
    1st
    2nd
    3rd
    4th
    5th
    6th
    Proceed to
    Actual gear position under malfunction
    Shift solenoid S1
    Stuck ON*1
    2nd
    2nd
    3rd
    4th
    5th
    6th
    A
    Stuck OFF
    1st
    1st
    3rd
    4th
    5th
    N*2
    Shift solenoid S2
    Stuck ON
    1st
    2nd
    2nd
    4th
    6th
    6th
    B
    Stuck OFF
    3rd
    3rd
    3rd
    4th
    5th
    5th
    Shift solenoid S3
    Stuck ON
    1st
    2nd
    3rd
    3rd
    N*2
    N*2
    C
    Stuck OFF
    3rd
    4th
    4th
    4th
    5th
    6th
    Shift solenoid S4
    Stuck ON*3
    1st
    2nd
    3rd
    4th
    5th
    6th
    D
    Stuck OFF
    1st
    2nd
    3rd
    4th
    4th
    4th
    Actual gear position when normal
    1st
    2nd
    3rd
    4th
    5th
    6th
    E

    HINT:
    1. *1: When shift solenoid S1 is stuck ON, the vehicle cannot drive in reverse.
    2. *2: Neutral
    3. *3: When shift solenoid S4 is stuck ON, gear shifting is normal.



B
Go to step 10

C
Go to step 13

D
Go to step 16

E
Go to step 20
A


4.INSPECT SHIFT SOLENOID VALVE S1


    C209925E04
  1. Remove the shift solenoid valve S1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid valve S1 connector terminal - Shift solenoid valve S1 body
    20°C (68°F)
    11 to 15 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) → Shift solenoid valve S1 connector
    2. Battery negative (-) → Shift solenoid valve S1 body
    Valve moves and makes an operating noise

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve S1)


NG
REPLACE SHIFT SOLENOID VALVE S1
OK


5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly.

    OK:
    There are no foreign objects on each valve.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


6.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Check the torque converter clutch assembly (Click here).

    OK:
    The torque converter clutch operates normally.



NG
REPLACE TORQUE CONVERTER CLUTCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)  

7.INSPECT SHIFT SOLENOID VALVE SLT


    C209928E06
  1. Remove shift solenoid valve SLT.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 2
    2. Battery negative (-) → Terminal 1
    Valve moves and makes an operating noise

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve SLT)


NG
REPLACE SHIFT SOLENOID VALVE SLT
OK


8.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly.

    OK:
    There are no foreign objects on each valve.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


9.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Check the torque converter clutch assembly (Click here).

    OK:
    The torque converter clutch operates normally.



NG
REPLACE TORQUE CONVERTER CLUTCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)  

10.INSPECT SHIFT SOLENOID VALVE S2


    C208650E03
  1. Remove the shift solenoid valve S2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid valve S2 connector terminal - Shift solenoid valve S2 body
    20°C (68°F)
    11 to 15 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) → Shift solenoid valve S2 connector
    2. Battery negative (-) → Shift solenoid valve S2 body
    Valve moves and makes an operating noise

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve S2)


NG
REPLACE SHIFT SOLENOID VALVE S2
OK


11.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly.

    OK:
    There are no foreign objects on each valve.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


12.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Check the torque converter clutch assembly (Click here).

    OK:
    The torque converter clutch operates normally.



NG
REPLACE TORQUE CONVERTER CLUTCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)  

13.INSPECT SHIFT SOLENOID VALVE S3


    C209925E05
  1. Remove the shift solenoid valve S3.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid valve S3 connector terminal - Shift solenoid valve S3 body
    20°C (68°F)
    11 to 15 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) → Shift solenoid valve S3 connector
    2. Battery negative (-) → Shift solenoid valve S3 body
    Valve moves and makes an operating noise

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve S3)


NG
REPLACE SHIFT SOLENOID VALVE S3
OK


14.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly.

    OK:
    There are no foreign objects on each valve.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


15.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Check the torque converter clutch assembly (Click here).

    OK:
    The torque converter clutch operates normally.



NG
REPLACE TORQUE CONVERTER CLUTCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)  

16.INSPECT SHIFT SOLENOID VALVE S4


    C208651E04
  1. Remove the shift solenoid valve S4.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid valve S4 connector terminal - Shift solenoid valve S4 body
    20°C (68°F)
    11 to 15 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) → Shift solenoid valve S4 connector
    2. Battery negative (-) → Shift solenoid valve S4 body
    Valve moves and makes an operating noise

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve S4)


NG
REPLACE SHIFT SOLENOID VALVE S4
OK


17.INSPECT SHIFT SOLENOID VALVE SL2


    C197715E12
  1. Remove the shift solenoid valve SL2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 1
    2. Battery negative (-) → Terminal 2
    Valve moves and makes an operating noise

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve SL2)


NG
REPLACE SHIFT SOLENOID VALVE SL2
OK


18.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly.

    OK:
    There are no foreign objects on each valve.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


19.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Check the torque converter clutch assembly (Click here).

    OK:
    The torque converter clutch operates normally.



NG
REPLACE TORQUE CONVERTER CLUTCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)  

20.INSPECT SHIFT SOLENOID VALVE SLT


    C209928E06
  1. Remove the shift solenoid valve SLT.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 2
    2. Battery negative (-) → Terminal 1
    Valve moves and makes an operating noise

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve SLT)


NG
REPLACE SHIFT SOLENOID VALVE SLT
OK


21.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly.

    OK:
    There are no foreign objects on each valve.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


22.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Check the torque converter clutch assembly (Click here).

    OK:
    The torque converter clutch operates normally.



NG
REPLACE TORQUE CONVERTER CLUTCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)