Home › Drivetrain ยท AB60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > REMOVAL

for Preparation Click here



1. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



2. DRAIN TRANSFER OIL


    C159809
  1. Remove the 4 bolts and lower transfer case protector.

  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket, and drain the transfer oil.



3. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



  1. Tighten the radiator drain cock plug by hand.


    A151835E01



4. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
  1. Remove the front propeller shaft assembly (Click here).



5. REMOVE PROPELLER SHAFT ASSEMBLY
  1. Remove the propeller shaft assembly (Click here).



6. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the heated oxygen sensor connector and detach the 2 clamps.



    A184982
  1. Remove the 2 bolts from the center exhaust pipe.

  1. Remove the 3 nuts, front exhaust pipe and 2 gaskets.



7. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY


A184981
  1. Remove the 2 bolts from the center exhaust pipe.

  1. Remove the 2 bolts and 2 nuts from the front No. 2 exhaust pipe sub-assembly.

  1. Disconnect the front No. 3 exhaust pipe sub-assembly from the exhaust pipe support.

  1. Remove the 2 gaskets.

  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the heated oxygen sensor connector.



    A184304
  1. Remove the 3 nuts, No. 2 exhaust pipe sub-assembly and gasket.



8. DISCONNECT WATER BY-PASS PIPE ASSEMBLY


    C162563
  1. Remove the bolt and disconnect the 2 water by-pass hoses from the transmission oil cooler. Then separate the by-pass pipe from the automatic transmission.

    HINT:
    Use a container to catch any coolant which flows out of the water by-pass hoses.



9. DISCONNECT NO. 2 OIL COOLER HOSE


    C162139
  1. Loosen the 2 clips and disconnect the inlet No. 2 oil cooler hose and outlet No. 2 oil cooler hose.



10. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    C155905
  1. Remove the nut and clip, and disconnect the transmission control cable.



11. REMOVE STARTER ASSEMBLY
  1. Remove the starter assembly (Click here).



12. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT


    C161354
  1. Turn the crankshaft to gain access to the 6 bolts and remove the bolts while holding the crankshaft pulley setting bolt with a wrench.



13. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY


    C161356
  1. Support the automatic transmission with a transmission jack. Lift the automatic transmission slightly from the crossmember.

    NOTICE:
    Position the jack so that it supports the oil pan bolt section, to prevent damage to the oil pan gasket.



14. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


    C162565
  1. Remove the 4 bolts of the rear No. 1 engine mounting insulator.



    C162566
  1. Remove the 4 nuts, 4 washers, 4 bolts and No. 3 frame crossmember.



15. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR


    C220065
  1. Remove the 4 bolts and rear No. 1 engine mounting insulator from the automatic transmission.



16. DISCONNECT WIRE HARNESS AND CONNECTOR


    C155915
  1. Remove the bolt and disconnect the ground cable.



    C162764E01
  1. Tilt the transmission downward.

    NOTICE:
    Make sure the cooling fan does not contact the fan shroud.



    C161361E01
  1. Disconnect the park/neutral position switch connector, 2 transmission wire connectors, 2 speed sensor connectors and 3 transfer control side connectors.

    HINT:
    Detach the claw, press down the lever, and then disconnect the transmission wire connector.

  1. Disconnect the 3 connector clamps and 7 harness clamps.

  1. Remove the 2 bolts and disconnect the harness clamps and wire harness.



17. DISCONNECT BREATHER PLUG HOSE


C161365
  1. Disconnect the 3 breather plug hoses from the harness clamp bracket.



18. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY


    C161364
  1. Remove the 10 bolts and automatic transmission.

    NOTICE:
    Do not use excess force when prying the automatic transmission.



19. REMOVE CONNECTOR CLAMP BRACKET
  1. Remove the 3 bolts and 3 oxygen sensor connector clamp brackets from the automatic transmission.



20. REMOVE TRANSMISSION CONTROL CABLE BRACKET


    C161369
  1. Remove the 2 bolts and transmission control cable bracket.



21. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Remove the torque converter clutch from the automatic transmission.



22. REMOVE TRANSFER ASSEMBLY


    C160352
  1. Remove the 8 transfer adaptor rear mounting bolts.

  1. Pull the transfer straight up and remove it from the transmission.

    NOTICE:
    Take care not to damage the rear adaptor oil seal with the transfer input gear spline.



23. INSPECT TORQUE CONVERTER CLUTCH AND DRIVE PLATE
  1. Inspect the torque converter clutch and drive plate (Click here).