Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1800/51    Short in Driver Side Squib Circuit

DTC    B1801/51    Open in Driver Side Squib Circuit

DTC    B1802/51    Short to GND in Driver Side Squib Circuit

DTC    B1803/51    Short to B+ in Driver Side Squib Circuit

for Preparation Click here


DESCRIPTION

  1. The driver side squib circuit consists of the center airbag sensor, the spiral cable, and the steering pad.
  2. The circuit instructs the SRS to deploy when deployment conditions are met.
  3. These DTCs are stored when a malfunction is detected in the driver side squib circuit.

DTC Code
Detection Condition
Trouble Area
B1800/51
When one of following conditions is met:
  1. The center airbag sensor receives a line short circuit signal 5 times in the driver side squib circuit during primary check.
  2. Driver side squib malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib)
  4. Center airbag sensor assembly
B1801/51
When one of following conditions is met:
  1. The center airbag sensor receives an open circuit signal in the driver side squib circuit for 2 seconds.
  2. Driver side squib malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib)
  4. Center airbag sensor assembly
B1802/51
When one of following conditions is met:
  1. The center airbag sensor receives a short circuit to ground signal in the driver side squib circuit for 0.5 seconds.
  2. Driver side squib malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib)
  4. Center airbag sensor assembly
B1803/51
When one of following conditions is met:
  1. The center airbag sensor receives a short circuit to B+ signal in the driver side squib circuit for 0.5 seconds.
  2. Driver side squib malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib)
  4. Center airbag sensor assembly

WIRING DIAGRAM


C180215E01


INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting "check mode" (signal check) with the intelligent tester (Click here).
  2. After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (Click here).

1.CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connector is properly connected to the steering pad.

    OK:
    The connector is properly connected.

    HINT:
    If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

  1. Disconnect the connector from the steering pad.

  1. Check that the spiral cable connector (on the steering pad side) is not damaged.

    OK:
    The lock button is not disengaged, or the claw of the lock is not deformed or damaged.



NG
REPLACE SPIRAL CABLE (Click here)
OK


2.CHECK STEERING PAD (DRIVER SIDE SQUIB)
C158844E06
  1. Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (orange connector).

    CAUTION:
    Never connect the tester to the steering pad (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1800, B1801, B1802, B1803 or 51 is not output.

    HINT:
    Codes other than DTC B1800, B1801, B1802, B1803 and 51 may be output at this time, but they are not related to this check.



NG
Go to step 3
OK

REPLACE STEERING PAD (Click here)  

3.CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector E.

  1. Check that the connector is properly connected to the center airbag sensor assembly.

    OK:
    The connector is properly connected.

    HINT:
    If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

  1. Disconnect the connector from the center airbag sensor assembly.

  1. Check that the terminal of the connector is not damaged.

    OK:
    The terminal is not deformed or damaged.

  1. Check that the short spring for the instrument panel wire connector with the activation prevention mechanism is not deformed or damaged.

    OK:
    The short spring is not deformed or damaged.



NG
REPLACE INSTRUMENT PANEL WIRE
OK


4.CHECK DRIVER SIDE SQUIB CIRCUIT
C158845E05
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    z7-2 (D+) - Body ground
    Ignition switch ON
    Below 1 V
    z7-1 (D-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z7-2 (D+) - z7-1 (D-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z7-2 (D+) - z7-1 (D-)
    Always
    1 MΩ or higher
    z7-2 (D+) - Body ground
    Always
    1 MΩ or higher
    z7-1 (D-) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 6
OK


5.CHECK CENTER AIRBAG SENSOR
C158846E01
  1. Restore the released activation prevention mechanism of connector B to the original condition.

  1. Connect the connectors to the steering pad and the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1800, B1801, B1802, B1803 or 51 is not output.

    HINT:
    Codes other than DTC B1800, B1801, B1802, B1803 and 51 may be output at this time, but they are not related to this check.

    Result 
    Result
    Proceed to
    OK
    A
    NG (w/ Cool Box)
    B
    NG (w/o Cool Box)
    C



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)  

6.CHECK CONNECTOR
  1. Restore the released activation prevention mechanism of connector B to the original condition.

  1. Check that the connectors that link the spiral cable and instrument panel wire harness are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors that link the spiral cable and instrument panel wire.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

  1. Check that the short spring for the spiral cable connector with the activation prevention mechanism is not deformed or damaged.

    OK:
    The short spring is not deformed or damaged.



NG
REPLACE SPIRAL CABLE OR INSTRUMENT PANEL WIRE
OK


7.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE)
C158847E09
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H13-1 (D+) - Body ground
    Ignition switch ON
    Below 1 V
    H13-2 (D-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H13-1 (D+) - H13-2 (D-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H13-1 (D+) - H13-2 (D-)
    Always
    1 MΩ or higher
    H13-1 (D+) - Body ground
    Always
    1 MΩ or higher
    H13-2 (D-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE SPIRAL CABLE (Click here)