DTC P0351 Ignition Coil "A" Primary / Secondary Circuit |
DTC P0352 Ignition Coil "B" Primary / Secondary Circuit |
DTC P0353 Ignition Coil "C" Primary / Secondary Circuit |
DTC P0354 Ignition Coil "D" Primary / Secondary Circuit |
DTC P0355 Ignition Coil "E" Primary / Secondary Circuit |
DTC P0356 Ignition Coil "F" Primary / Secondary Circuit |
DTC P0357 Ignition Coil "G" Primary / Secondary Circuit |
DTC P0358 Ignition Coil "H" Primary / Secondary Circuit |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0351 P0352 P0353 P0354 P0355 P0356 P0357 P0358 | No IGF signal to ECM while engine running (1 trip detection logic) |
|
![]() |
| Tester Connection | Tool Setting | Condition | Specified Condition |
| D56-40 (IGT1) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling | The correct waveform is as shown |
| D56-33 (IGT2) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling | The correct waveform is as shown |
| D56-37 (IGT3) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling | The correct waveform is as shown |
| D56-34 (IGT4) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling | The correct waveform is as shown |
| D56-35 (IGT5) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling | The correct waveform is as shown |
| D56-36 (IGT6) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling | The correct waveform is as shown |
| D56-38 (IGT7) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling | The correct waveform is as shown |
| D56-39 (IGT8) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling | The correct waveform is as shown |
| D56-104 (IGF1) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling | The correct waveform is as shown |
| D56-105 (IGF2) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling | The correct waveform is as shown |



| 1.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the ignition coil with igniter connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D5-4 (GND) - Body ground | Always | Below 1 Ω |
| D13-4 (GND) - Body ground | Always | Below 1 Ω |
| D6-4 (GND) - Body ground | Always | Below 1 Ω |
| D12-4 (GND) - Body ground | Always | Below 1 Ω |
| D7-4 (GND) - Body ground | Always | Below 1 Ω |
| D11-4 (GND) - Body ground | Always | Below 1 Ω |
| D8-4 (GND) - Body ground | Always | Below 1 Ω |
| D10-4 (GND) - Body ground | Always | Below 1 Ω |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D5-1 (+B) - D5-4 (GND) | Ignition switch ON | 11 to 14 V |
| D13-1 (+B) - D13-4 (GND) | Ignition switch ON | 11 to 14 V |
| D6-1 (+B) - D6-4 (GND) | Ignition switch ON | 11 to 14 V |
| D12-1 (+B) - D12-4 (GND) | Ignition switch ON | 11 to 14 V |
| D7-1 (+B) - D7-4 (GND) | Ignition switch ON | 11 to 14 V |
| D11-1 (+B) - D11-4 (GND) | Ignition switch ON | 11 to 14 V |
| D8-1 (+B) - D8-4 (GND) | Ignition switch ON | 11 to 14 V |
| D10-1 (+B) - D10-4 (GND) | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM) |
Disconnect the ignition coil with igniter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D5-2 (IGF1) - D56-104 (IGF1) | Always | Below 1 Ω |
| D13-2 (IGF2) - D56-105 (IGF2) | Always | Below 1 Ω |
| D6-2 (IGF2) - D56-105 (IGF2) | Always | Below 1 Ω |
| D12-2 (IGF1) - D56-104 (IGF1) | Always | Below 1 Ω |
| D7-2 (IGF2) - D56-105 (IGF2) | Always | Below 1 Ω |
| D11-2 (IGF1) - D56-104 (IGF1) | Always | Below 1 Ω |
| D8-2 (IGF1) - D56-104 (IGF1) | Always | Below 1 Ω |
| D10-2 (IGF2) - D56-105 (IGF2) | Always | Below 1 Ω |
| D5-3 (IGT1) - D56-40 (IGT1) | Always | Below 1 Ω |
| D13-3 (IGT2) - D56-33 (IGT2) | Always | Below 1 Ω |
| D6-3 (IGT3) - D56-37 (IGT3) | Always | Below 1 Ω |
| D12-3 (IGT4) - D56-34 (IGT4) | Always | Below 1 Ω |
| D7-3 (IGT5) - D56-35 (IGT5) | Always | Below 1 Ω |
| D11-3 (IGT6) - D56-36 (IGT6) | Always | Below 1 Ω |
| D8-3 (IGT7) - D56-38 (IGT7) | Always | Below 1 Ω |
| D10-3 (IGT8) - D56-39 (IGT8) | Always | Below 1 Ω |
| D5-2 (IGF1) or D56-104 (IGF1) - Body ground | Always | 10 kΩ or higher |
| D13-2 (IGF2) or D56-105 (IGF2) - Body ground | Always | 10 kΩ or higher |
| D6-2 (IGF2) or D56-105 (IGF2) - Body ground | Always | 10 kΩ or higher |
| D12-2 (IGF1) or D56-104 (IGF1) - Body ground | Always | 10 kΩ or higher |
| D7-2 (IGF2) or D56-105 (IGF2) - Body ground | Always | 10 kΩ or higher |
| D11-2 (IGF1) or D56-104 (IGF1) - Body ground | Always | 10 kΩ or higher |
| D8-2 (IGF1) or D56-104 (IGF1) - Body ground | Always | 10 kΩ or higher |
| D10-2 (IGF2) or D56-105 (IGF2) - Body ground | Always | 10 kΩ or higher |
| D5-3 (IGT1) or D56-40 (IGT1) - Body ground | Always | 10 kΩ or higher |
| D13-3 (IGT2) or D56-33 (IGT2) - Body ground | Always | 10 kΩ or higher |
| D6-3 (IGT3) or D56-37 (IGT3) - Body ground | Always | 10 kΩ or higher |
| D12-3 (IGT4) or D56-34 (IGT4) - Body ground | Always | 10 kΩ or higher |
| D7-3 (IGT5) or D56-35 (IGT5) - Body ground | Always | 10 kΩ or higher |
| D11-3 (IGT6) or D56-36 (IGT6) - Body ground | Always | 10 kΩ or higher |
| D8-3 (IGT7) or D56-38 (IGT7) - Body ground | Always | 10 kΩ or higher |
| D10-3 (IGT8) or D56-39 (IGT8) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355, P0356, P0357 OR P0358) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Clear DTCs (Click here).
Shuffle the arrangement of the ignition coils with igniters (among No. 1 to No. 8 cylinders).
Perform a simulation test.
Check DTCs displayed on the intelligent tester.
| Result | Proceed to |
| Same DTC is output | A |
| Different ignition coil DTC is output | B |
|
| ||||
| A | ||
| ||